Subject	I just replaced my line/slave and bled the system 2 days
Posted by	whitepearlz on May 19, 2005 at 10:42 AM
	This message has been viewed 155 times.
In Reply To	Clutch Slave.... posted by 300ZMang on May 19, 2005 at 09:55 AM
Message	ago. After finding out the banjo bolt provided with my clutch line was too short, everything went perfectly. I used Speedbleeders at both bleed points, and I couldn't imagine it without them. Basically, open up the bleeder on your slave cylinder until it falls out. Have a small pan or something underneath it, and all of the fluid will drain out. There isn't much more than a few ounces of fluid in the whole clutch system. Replace the slave cylinder and line (very easy without lifting the car much, IMO). Fill the master cylinder with fluid and bleed each point a few times. You'll know you're getting there when the pedal starts building up some good, permanent pressure. "funny how I like the a spec fascia more and more now that I have the j spec" - CLOWNSHUE on April 04, 2005 at 2:42 PM WINTER (Also known as a "WISCONSIN WINTER") This is one of Wisconsin's two seasons which lasts approximately 9 months. The other season is the ROAD CONSTRUCTION season, lasting roughly 3 months.
Follow Ups	Clutch Slave.... - 300ZMang 09:55:54 05/19/05 Coz has a SS braided line too - NA300zx (OH) 10:02:01 05/19/05 they shouldn't have to drain the tranny. - rufflez 10:02:36 05/19/05 Why not get SGP's line? They do not drain the tranny - Guapo 10:05:12 05/19/05 Ok... so I could do the slave cylinder myself.. - 300ZMang 10:12:01 05/19/05 the SS line connects the slave to the master cylinder - NA300zx (OH) 10:15:16 05/19/05 well ... - Guapo 10:18:14 05/19/05 speed bleeders make it much easier. (n/m) - silver2+2TT (MD) 10:37:21 05/19/05 What are the speed bleeder part numbers?? (n/m) - Gordo 93TT NYC 10:49:38 05/19/05 speed bleeder's part# SB7100 (7MM, 1.0 thread pitch) - CAP927 (Boston) 12:28:18 05/19/05 Thanks CAP, I use them on Brake Calipers, but could not find - Gordo 93TT NYC 13:15:52 05/19/05 I just replaced my line/slave and bled the system 2 days - whitepearlz 10:42:52 05/19/05 you shouldn't need to open the bleeder that far. - Guapo 10:59:42 05/19/05 Right, I was on the speedbleeder mind-set there. =) (n/m) - whitepearlz 11:31:41 05/19/05 you shouldn't need to open the speedbleeder that far (n/m) - Guapo 12:20:12 05/19/05 To completely drain the system? It's sure quicker. (n/m) - whitepearlz 12:27:55 05/19/05 Where did you get your SS line? - U ZCREAM 11:05:00 05/19/05 I got mine from SPL, and it came with the banjo bolt and two - whitepearlz 11:30:32 05/19/05 2cd. The banjo bolt I got from SGP for my ss line was also - Haasz32 11:24:52 05/19/05 Free bleeders from SPL :) (n/m) - The Sixth 10:49:51 05/19/05 2 totally seperate systems - sparkie 11:23:13 05/19/05 So in like basic steps.... - 300ZMang 12:26:28 05/19/05 Do you even know where to find the slave. - myzislow 12:49:00 05/19/05 Yes... I know where it is... and what it looks like - 300ZMang 13:36:47 05/19/05 OK Mang - myzislow 13:40:42 05/19/05 He's trying to determine if you're in over your head - spicyZ 15:46:29 05/19/05 some pics - robo (sebring1970) 21:58:33 05/19/05
Post a Followup	You cannot reply to this message because you are not logged in.