Subject	agree'd totally. as for the bottomend
Posted by	genic on May 18, 2005 at 1:57 PM
	This message has been viewed 26 times.
In Reply To	Patience. Attention to detail. posted by JRH(KY) on May 18, 2005 at 01:25 PM
Message	i would get a machine shop to do it imho. i didnt do the bottom end of mine other than the bearings being replaced. i didnt even remove the pistons...so i didnt deal with that. double check things, tread locker, follow the torque specs to the T, ask a lot of questions if you dont know how to do something. ask someone who cares though cause if you ask someone who doesnt care..they will just dick you around (heh..jk)
Follow Ups	Beginning engine rebuild...any advice for a first timer? - Zeus 12:34:56 05/18/05 Take a look @ Greg's TECH on it too. (n/m) - YugoBernie (NoVA) 12:35:58 05/18/05 Already read it over... - Zeus 12:40:27 05/18/05 excellent resource for the first timer. i used it a LOT (n/m) - genic 12:55:30 05/18/05 Get qualified help from ZEngineer :D - Fly'n Z 12:44:34 05/18/05 Zeus who? - ZEngineer 13:55:57 05/18/05 Leave it to the experts? - spicyZ 12:48:25 05/18/05 Where's the fun in that? =) (n/m) - Zeus 12:55:17 05/18/05 Agree, you would never know until you do it once. - nowayout 13:13:17 05/18/05 I'm busy - TARGETZ 17:41:19 05/18/05 did you find a Z? (n/m) - JDMz32smity 12:59:33 05/18/05 engine first, rolling chassis later. (n/m) - ZEngineer 14:23:57 05/18/05 Speaka only whena spokena to (n/m) - BigTDogg (MA) 14:32:11 05/18/05 look who speak sandy (n/m) - JDMz32smity 14:33:04 05/18/05 What George said =) (n/m) - Zeus 14:35:07 05/18/05 I just went through this about 2months ago for the first - JokerF15 (NyxMotorsports) 13:13:23 05/18/05 I might take you up on that, thanks! (n/m) - Zeus 14:39:08 05/18/05 Patience. Attention to detail. - JRH(KY) 13:25:07 05/18/05 agree'd totally. as for the bottomend - genic 13:57:44 05/18/05 Patience is definetly something I have plenty of - Zeus 14:48:19 05/18/05 k (n/m) - genic 14:54:11 05/18/05 I take it you have to deal with him on a regular basis? (n/m) - JRH(KY) 15:13:13 05/18/05 no, not really...he knows what my comment means... - Zeus 15:16:45 05/18/05 Make sure you put in your oil baffles and squirters - boileralum 14:17:09 05/18/05 that sounded like first hand experience ;) (n/m) - Zeus 14:36:42 05/18/05 mayhaps ;-) (n/m) - boileralum 15:57:15 05/18/05 Dont forget to use lube! - CrazyGreek 17:38:46 05/18/05 will do...efharisto (n/m) - Zeus 19:09:53 05/18/05 np, parakalo (n/m) - CrazyGreek 15:31:36 05/19/05 Clean...Keep everything clean. Cover or plug anything open. - Gordo 93TT NYC 21:15:58 05/18/05 Thanks Gordo...if anyone knows clean, it's you =) (n/m) - Zeus 09:12:16 05/19/05 Thanks, Also remember to bag and mark parts and fasteners. - Gordo 93TT NYC 09:38:28 05/19/05 way ahead of you there... - Zeus 11:18:31 05/19/05 use a tap to clean out threads. use red loctite - scubasteve (rebuilding) 11:45:00 05/19/05 every little bit helps...thanks! (n/m) - Zeus 12:53:55 05/19/05
Post a Followup	You cannot reply to this message because you are not logged in.