Subject	I've just seen a lot of problems with the gauges losing
Posted by	Ash's Z on April 22, 2005 at 6:51 PM
	This message has been viewed 68 times.
In Reply To	bah, autometer has been around a long time posted by Z32POWER.com on April 22, 2005 at 05:40 PM
Message	calibration and perhaps I should have stated it that way rarther than pointing out what I think of their appearance. I've been through two autometer boost gauges that have lost calibration and would sit at some value other than zero when the engine was off and I have also seen this occur with other types of autometer's gauges on a few other cars over time. I think comparatively speaking, the autometer is a good bang for the buck - greddy gauges are a bit more expensive.. [ ashspecz.com ] [ agpowers@bellsouth.net ] Enthusiasts soon understand each other. --W. Irving. Are you an enthusiast? If you are out to describe the truth, leave elegance to the tailor. Albert Einstein
Follow Ups	looking to get a more accurate water temp gauge - mousersix (San Antonio) 17:01:59 04/22/05 I have become quite fond of the Greddy gauges and less - Ash's Z 17:06:55 04/22/05 bah, autometer has been around a long time - Z32POWER.com 17:40:45 04/22/05 i agree also i only use autometer (n/m) - traydogg6969(Pittsburgh) 17:48:17 04/22/05 Love my Autometer guages. Don't care for Celcius readings (n/m) - AzHeat 18:09:48 04/22/05 seconded; - nixit 18:27:21 04/22/05 nice floor mats :) (n/m) - ZBlacktt 18:30:10 04/22/05 2nd, was about to coment on them (n/m) - rufflez 18:37:20 04/22/05 :) rhino lined the interior of the jeep. - nixit 18:41:34 04/22/05 Well - ZBlacktt 18:44:13 04/22/05 Nice looking Jeep bro - is that the jeep with the LS1 in it? (n/m) - Ash's Z 19:11:56 04/22/05 Twin Turbo LT1 - nixit 19:57:40 04/22/05 Nice. (n/m) - Tissan© 21:00:51 04/22/05 2nd! (n/m) - Ash's Z 21:41:28 04/22/05 that's just sick :) (n/m) - komplexZ 22:11:17 04/22/05 now thats badass! (n/m) - ZXRider(SoCal) 00:16:56 04/23/05 Do you offroad? How does it perform off the street? - mds2004 00:29:44 04/23/05 I've just seen a lot of problems with the gauges losing - Ash's Z 18:51:22 04/22/05 Out of the subject, can you tell me what did - ZCRZY 19:52:05 04/22/05 I did a post-welding stress relief heat treatment to the - Ash's Z 20:36:43 04/22/05 Thanks - ZCRZY 20:11:24 04/23/05 I like my greddy gauges, but not too big on the way - Zdude32 21:13:31 04/22/05 pffft...autometer functions quite well. - Spee 13:16:22 04/23/05 I use autometer gauge, works fine (n/m) - Magnum 17:07:20 04/22/05 try stewart warner (n/m) - asdafug 19:33:44 04/22/05 Autometer is the best option if you are on a - ZCRZY 19:59:26 04/22/05 I have defi but for the budget get greddy's - nowayout 21:42:37 04/22/05 i sure hope for 200+ dollars.... - JD_SMOOTH83 22:13:30 04/22/05 My VDO reads right on when compared to Conzult and such. (n/m) - Woody75 (Denver) 23:30:20 04/22/05 Get a (black) Techtom CMX. Plugs into the Consult port. (n/m) - Got Z? 16:24:58 04/23/05
Post a Followup	You cannot reply to this message because you are not logged in.