Subject	I have them wrapped on my Z's Dp and mids. As for
Posted by	Spongerider :) on April 21, 2005 at 11:01 PM
	This message has been viewed 39 times.
In Reply To	Wrapping DP's. Good, bad? > posted by whitepearlz on April 21, 2005 at 08:16 PM
Message	power, I don't know if it makes any differance but I did notice that when I'm driving the stick shift was not warm to the touch and the firewall next to your right foot did not get hot. www.SoCalZCrew.com **Dynoed at 371.2 rwhp. and 362.3 rwtrq. @ .9 bar on pumped 91 gas no time tweaking 3/11/03** **Dynoed at 411 rwhp. and 452 rwtq. @1.15 kg. on race gas 104 no time tweaking 3/28/03 **All numbers are SAE corrected**
Follow Ups	Wrapping DP's. Good, bad? > - whitepearlz 20:16:06 04/21/05 Good question. I would like to add to that - Spddracer 20:20:50 04/21/05 Wrapping has no effect on noise/resonance. (n/m) - Dave N 20:38:41 04/21/05 Correct....The resonance comes from the free flow of ..... - Greg D. (Specialty-Z) 20:52:08 04/21/05 Also from type of steel you use.....and thickness (n/m) - sweet z (UTAH) 00:55:57 04/22/05 get them Jet Hot coated (n/m) - Spee 20:34:03 04/21/05 2nd'd. (n/m) - Dave N 20:37:42 04/21/05 hey dave did u get my E-mail? (n/m) - Rickytl (MA) 20:48:23 04/21/05 Yep, I'm replying to it.... (n/m) - Dave N 20:52:24 04/21/05 ::shivers^spine:: - Rickytl (MA) 20:55:00 04/21/05 Jethot vs Ceramic coating? - JokerF15 (NyxMotorsports) 00:39:04 04/22/05 nm just got a good link on it... (n/m) - JokerF15 (NyxMotorsports) 00:40:28 04/22/05 I would think moisture would evaporate on dp's - 300zxer 20:37:40 04/21/05 some peeps feel condensation can form during the cool - robo (sebring1970) 21:59:11 04/21/05 Re: Wrapping DP's. Good, bad? > - Greg D. (Specialty-Z) 20:50:45 04/21/05 So is it the same impact with ceramic coating? (n/m) - Dave N 20:53:56 04/21/05 Correct, It would retain more heat and have less temp - Greg D. (Specialty-Z) 20:55:59 04/21/05 what about adding heat sheilds? - Rickytl (MA) 21:02:43 04/21/05 *smack* (n/m) - Dave N 21:05:32 04/21/05 It would depend where the heat shield was placed.... - Greg D. (Specialty-Z) 21:06:44 04/21/05 Interesting...I wonder if there is a tangible difference. - Dave N 21:11:56 04/21/05 Re: Interesting...I wonder if there is a tangible difference. - Rickytl (MA) 21:14:04 04/21/05 Re: Interesting...I wonder if there is a tangible difference. - Greg D. (Specialty-Z) 21:48:01 04/21/05 So, would you say leaving them un-wrapped outweighs - whitepearlz 20:59:23 04/21/05 The best way to answer your question is to say ...... - Greg D. (Specialty-Z) 21:08:26 04/21/05 Thanks, all I needed to know. =) - whitepearlz 21:13:20 04/21/05 If they were mine i would put tacks around the flange - Tissan© 21:23:37 04/21/05 Re: Thanks, all I needed to know. =) - Greg D. (Specialty-Z) 21:41:13 04/21/05 Thanks Greg, I think I will take you up on that. =) - whitepearlz 21:51:12 04/21/05 Any issues with the SS splits version from ~10/03? (n/m) - USCZ 17:27:06 04/22/05 I won't be wrapping mine either. (n/m) - ZFreak (Dallas) 22:34:23 04/21/05 im wrapping mine for temp control only. - genic 23:09:41 04/21/05 Re: im wrapping mine for temp control only. - Greg D. (Specialty-Z) 23:24:22 04/21/05 FYI.....The pipes really do not get too hot without cats. (n/m) - Greg D. (Specialty-Z) 23:28:36 04/21/05 what about shields or wrap on the intake piping - genic 23:12:00 04/21/05 Re: what about shields or wrap on the intake piping - Greg D. (Specialty-Z) 23:26:52 04/21/05 i did that...and what i found after i took it off.. - genic 08:52:40 04/22/05 I agree to a point. (n/m) - sweet z (UTAH) 01:00:15 04/22/05 I agree to a point - sweet z (UTAH) 01:03:31 04/22/05 I want to see the proof of reduced underhood temps. - robo (sebring1970) 21:14:54 04/21/05 I coated mine for the warranty and I figured - Fuzznutz 22:57:57 04/21/05 we need to tape a thermometer to the bottom of someone's - robo (sebring1970) 23:15:41 04/21/05 Heh, maybe so... - Fuzznutz 23:20:06 04/21/05 I have them wrapped on my Z's Dp and mids. As for - Spongerider :) 23:01:54 04/21/05
Post a Followup	You cannot reply to this message because you are not logged in.