Subject	Yep. >>
Posted by	Ash's Z on February 22, 2005 at 11:16 PM
	This message has been viewed 211 times.
In Reply To	I like the design. You checked the side clearance posted by AzHeat on February 22, 2005 at 11:12 PM
Message	Theres actually a good 2" between the compressor and the framing rail, this is just an odd angle. I'm looking forward to being able to pull these puppies out without pulling the engine too. :) [ ashspecz.com ] [ agpowers@bellsouth.net ] Enthusiasts soon understand each other. --W. Irving. Are you an enthusiast? If you are out to describe the truth, leave elegance to the tailor. Albert Einstein
Follow Ups	AshsZ-II Ultimate Street Z Progress >>> MANIFOLDS - Ash's Z 21:45:07 02/22/05 you do good work :) (n/m) - Tissan© 21:47:25 02/22/05 You're a cross between Mr. Wizard and Mcguyver - Moxie 21:48:10 02/22/05 mcguyver could make it with a quarter and a - Ebola 21:50:08 02/22/05 Don't forget the chewing gum - Steve-O 21:57:54 02/22/05 Snorkel and an avocado (n/m) - aggiez32 07:14:16 02/23/05 dont forget the corkscrew (n/m) - atl300zxtt 07:56:07 02/23/05 Those are like a work of art - sfpearl300z 21:48:58 02/22/05 very well done! (n/m) - Ballistic 21:49:56 02/22/05 Simply amazing! and your wife helped too... - ZXRider(SoCal) 21:51:05 02/22/05 Looks nice so far, - Ebola 21:51:58 02/22/05 I was going to ask about equal length as well (n/m) - twinturbineZ 21:59:22 02/22/05 I am going for a hybrid design between log style and equal - Ash's Z 22:02:57 02/22/05 equal length would be way better (n/m) - 90BlkZ18 22:08:48 02/22/05 I would like to see some conclusive data to back that idea - Ash's Z 22:13:15 02/22/05 yah id like to see a comparason of tuned v. not. - 90BlkZ18 22:14:27 02/22/05 Here is some data. - Ozone240 23:01:25 02/22/05 Nice! I also like how they too are finding that the MAS is - Ash's Z 23:12:59 02/22/05 nicely done. Looks great. (n/m) - Evan(MS) 23:11:26 02/22/05 Manifold 'tuning' isn't as big an issue with turbos - PhishZ 09:57:55 02/23/05 I see, nice work, it would be interesting - Ebola 22:11:08 02/22/05 i would pay the little bit of extra and have them cryo'ed - joker_20_02 (Rebuilding) 22:32:24 02/22/05 That is actually a really good idea. I've wondered about - Ash's Z 22:37:34 02/22/05 jet hot is suppose to be the same concept, right? - Rbadger 22:50:04 02/22/05 Thermal coatings (like what Jet-HOT offers) are insulating - Ash's Z 23:05:56 02/22/05 I'm curious to see how they stand up to the heat, long term. - CarlCuro 23:29:07 02/22/05 Me too. I will be adding some reinforcement tabs to the - Ash's Z 00:03:22 02/23/05 contact info - Luke@tirerack 07:27:58 02/23/05 Thanks Luke! (n/m) - Ash's Z 11:57:20 02/23/05 they're the same people who do www.FrozenRotors.com (n/m) - Luke@tirerack 12:49:18 02/23/05 Nice design Ash i got to hand it you >>>> - SL103 23:44:48 02/22/05 they will flow better than a log, they will work well (n/m) - Z32POWER.com 08:40:23 02/23/05 What gauge piping are you using, Ash? (n/m) - boileralum 21:56:21 02/22/05 16-gauge. (n/m) - Ash's Z 22:05:10 02/22/05 Very nice job! Love seeing posts like this. (n/m) - TheTwinZ (Peru) 21:56:52 02/22/05 2nded (n/m) - thunderZ 22:15:57 02/22/05 Nice...awesome work! - BradZ (FL) 22:01:21 02/22/05 No coatings but I will be shielding them pretty well. (n/m) - Ash's Z 22:09:11 02/22/05 Re: AshsZ-II Ultimate Street Z Progress >>> MANIFOLDS - zdoc 22:03:26 02/22/05 Comming along nicely (n/m) - Poom (Pittsburgh) 22:11:17 02/22/05 nice ash, very nice (n/m) - VG30DE racer 22:15:58 02/22/05 You sir, are a Fab Whore x 1000. :) - ZFreak (Dallas) 23:07:35 02/22/05 I like the design. You checked the side clearance - AzHeat 23:12:22 02/22/05 Yep. >> - Ash's Z 23:16:37 02/22/05 Small compressor. Mine cleared by 1/4 inch on the - AzHeat 23:32:26 02/22/05 eh? That's a 62-trim T3 compressor wheel in a T04B housing. - Ash's Z 23:55:09 02/22/05 DAMN ! (n/m) - rave 23:16:48 02/22/05 So how much does Ash charge for rebuild? - Lynxbat 23:23:28 02/22/05 That would be for a classified post or an email. - Ash's Z 23:58:14 02/22/05 will e-mail from work (n/m) - Lynxbat 06:33:44 02/23/05 jw: Any reason why you didn't do equal-length? (n/m) - NytWolf 23:26:10 02/22/05 here you go - ZXRider(SoCal) 23:28:23 02/22/05 Ahh, thanks ... (n/m) - NytWolf 23:30:18 02/22/05 You do some really good work! Love the color on the engine! (n/m) - TBlakeZ 23:28:29 02/22/05 Hows OBII coming.... - Zluster(Project Platypus) 23:36:54 02/22/05 2nd Ash - golden_1 01:15:41 02/23/05 Use money for paint, suspension, fixing dash gauges, etc.... (n/m) - Woody75 (Denver) 08:16:37 02/23/05 in may yes... - Zluster(Project Platypus) 00:00:59 02/24/05 Nice, Ash. 16 gauge stainless steel? 321? (n/m) - Scotts94z32 00:16:20 02/23/05 Yup. I decided to go with the thicker material after lookin - Ash's Z 00:37:12 02/23/05 Plus, the weld quality is better for 321 versus 304 SS - Scotts94z32 16:01:38 02/23/05 Great information there Scott. I was aware of the titanium - Ash's Z 16:53:36 02/23/05 The look beautiful - its a shame they will crack. - maglito 00:37:29 02/23/05 Heh, yeah, they will crack eventually. Hopefully later than - Ash's Z 00:44:01 02/23/05 very nice work ash.. - zads 01:41:57 02/23/05 Re: very nice work ash.. - Ash's Z 02:26:34 02/23/05 UR da best. how much $$ have U drop so far though? (n/m) - E=m[91NA-(2+2)-(5sp)]² 07:44:10 02/23/05 $225 for the 321 SS pipes and $60 for the flanges. So, $285 - Ash's Z 11:56:39 02/23/05 you are a very talented person. (n/m) - Nazgul 08:00:20 02/23/05 I'm impressed, you have a lot of skill. (n/m) - whitepearlz 08:38:16 02/23/05 Gonna need a bigger garage soon... (n/m) - Gordo 93TT NYC 15:37:35 02/23/05 I've been eyeballing a couple of buildings not far from here - Ash's Z 16:57:29 02/23/05 Looks like you are going to need a Business Plan also. - Gordo 93TT NYC 20:07:41 02/23/05 Much appreciated - I look forward to hearing from you! (n/m) - Ash's Z 22:49:53 02/23/05 any plans on external wastegate manifolds??? (n/m) - Carp (Show & Go) 16:34:54 02/23/05 Well, these are just personals, so, no. - Ash's Z 22:53:21 02/23/05
Post a Followup	You cannot reply to this message because you are not logged in.