Subject	I wish I could but I don't have the time
Posted by	CarbonZTT on February 17, 2005 at 9:51 AM
	This message has been viewed 35 times.
In Reply To	why not make them re-do it, and do it right? posted by Waco300zx on February 17, 2005 at 09:40 AM
Message	They have had my car since september, it was suppose to be done end of Oct. Obviously they are a little behind. I need my car back as I have other stuff I have to get done and finish before spring. I'm not sure I'd want them doing anything else to my car anyway. The managment of the shop is horrible, I've been lyed to and srewed around so much that i just want my car out of there. But this isn't really the issue I need to figure out what to do with my door panel now, or else my car will bet there forever. I just want to get all this over with. TeamSolo Sponsors -Power Supply Racing -TheTwinZ (Peru) -Ionicdynamics.com
Follow Ups	Cutting my door panels to fit my cage.Need some help - CarbonZTT 08:47:15 02/17/05 Re: Cutting my door panels to fit my cage.Need some help - CRAZZEPETE. 08:51:18 02/17/05 mine is custom and different (n/m) - CarbonZTT 08:52:16 02/17/05 hackjob is more accurate - aliaZ 09:38:34 02/17/05 2nd. You're paying good money I'm sure... Get your $$'s - Waco300zx 09:41:30 02/17/05 The rollcage mounting place is too close to the door - Stickeefingerz 09:19:34 02/17/05 I think I have to agree... (n/m) - Waco300zx 09:22:39 02/17/05 looks like ... - Guapo 09:24:54 02/17/05 2nd.... - Kyle(Houston) 09:28:10 02/17/05 yes but regardless I now have to cut the interior - CarbonZTT 09:37:54 02/17/05 why not make them re-do it, and do it right? - Waco300zx 09:40:46 02/17/05 I wish I could but I don't have the time - CarbonZTT 09:51:55 02/17/05 Get your car back! - cruzinZ 10:04:14 02/17/05 well good advice but the shop came very highly recomended - CarbonZTT 10:09:43 02/17/05 At some point very soon it SHOULD be the point - SeedyROM 14:05:16 02/17/05 Curious: Is it a CT shop? - trackstar 10:10:41 02/17/05 I would never accept that - TARGETZ 09:35:32 02/17/05 Yeah, there is no need for him to mess w/ the panels - Seb (Specialty-Z) 10:10:30 02/17/05 ^^^^ ditto (n/m) - JDMz32smity 10:16:59 02/17/05 How much rework would it take to move the cage in a couple - atl300zxtt 10:27:33 02/17/05 Make them redo the cage. Thats ridiculous. (n/m) - Kenny 10:44:52 02/17/05 Dude, I don't thing all that cutting was necessary. >> - Arnel@Z32racing.com 10:46:44 02/17/05 Do you have more pics of ur cage? - atl300zxtt 10:48:27 02/17/05 $1300. >> - Arnel@Z32racing.com 11:30:46 02/17/05 F. that, for what you paid, they need to fix the cage. - YugoBernie (NoVA) 10:47:03 02/17/05 make them redo it anyway ... - Guapo 10:51:46 02/17/05 2nd...This cage does look very different compared to Arnels (n/m) - atl300zxtt 10:55:52 02/17/05 3thed. In fact, it looks like the diagonal bar is not 1 - boileralum 14:07:21 02/17/05 You know.... - aggiez32 11:02:36 02/17/05 2nd. :-( (n/m) - Spongerider :) 16:17:13 02/17/05 I'd write-it off & start-over with Arnel's guy (n/m) - NAZTTy 11:04:52 02/17/05 Think of how bad that will look with the door open. - fantomZ(OH) 11:11:17 02/17/05 ok I understand all of the comments about the cage postionin - Luke@tirerack 11:16:35 02/17/05 best solution yet i think - atl300zxtt 11:18:41 02/17/05 I was looking at other pics of your cage..can u put down - atl300zxtt 11:17:08 02/17/05 no, i also have to get another rear view mirror (n/m) - CarbonZTT 11:41:27 02/17/05 thats horrible man... i hope there is good cause - Z32POWER.com 11:51:23 02/17/05 Holy Hackjob... Try not to rely on welds for strength... - Scotts94z32 12:55:46 02/17/05 Now Scott, don't be silly. Of course he isn't. (n/m) - Kenny 13:30:09 02/17/05 good call (n/m) - CarbonZTT 14:54:01 02/17/05 Doors..? you mean the doors are supposed to be closed...? (n/m) - Tu 14:10:28 02/17/05 Honestly - sweet z (UTAH) 14:51:25 02/17/05 I just got back from the shop, The panels look good now - CarbonZTT 15:20:58 02/17/05 Re: I just got back from the shop, The panels look good now - Sportzcoop 17:20:31 02/17/05 You sir are a moron (n/m) - TARGETZ 19:23:10 02/17/05
Post a Followup	You cannot reply to this message because you are not logged in.