Subject	I used plywood and two 2x4 nailed to each side and
Posted by	AzHeat on January 19, 2005 at 5:08 PM
	This message has been viewed 15 times.
In Reply To	put the drain in the middle of the jack, and use the belt posted by boileralum on January 19, 2005 at 04:03 PM
Message	the tranny is secure and balanced. No need for chain loop. BTW, once you jack up the tranny into the tunnel, there is no room to remove the chain from the tranny jack. Chain was useless.
Follow Ups	I have a new level of respect for you guys that work - ConVerTT 11:32:47 01/19/05 Thank you, thank you (bow) :) (n/m) - Haasz32 11:34:45 01/19/05 2nd (n/m) - ForceFedZ32 (SoCal) 12:11:16 01/19/05 actually, I bet the 2 bolts would be easier on the ground... - Waco300zx 11:39:10 01/19/05 Working on these cars in general for that matter :>P (n/m) - BrianTT(TPA,FL) 11:47:13 01/19/05 been there... not fun (n/m) - DragonSi 11:49:33 01/19/05 bah ... just wait til you have to get it back on :) (n/m) - Guapo 11:51:15 01/19/05 No kidding... - 90Z-NA (ATL) 11:53:44 01/19/05 ever hear of a transmission jack ? - Luke@tirerack 12:22:23 01/19/05 For those of use w/o lifts - boileralum 12:42:59 01/19/05 I have that and it works awesome. - Woody75 (Denver) 12:48:16 01/19/05 yep (n/m) - Guapo 12:51:17 01/19/05 I help PunkZ with that jack. The problem with the jack - AzHeat 13:03:56 01/19/05 put the drain in the middle of the jack, and use the belt - boileralum 16:03:29 01/19/05 I used plywood and two 2x4 nailed to each side and - AzHeat 17:08:57 01/19/05 Like I need another expense :-| (n/m) - 90Z-NA (ATL) 12:44:39 01/19/05 I am using a tranny jack also. See - even more respect - ConVerTT 12:40:56 01/19/05 Doing it w. out a tranny jack is foolish and dangerous. (n/m) - YugoBernie (NoVA) 12:56:13 01/19/05 Agreed. I worked up a pretty good sweat even with the jack (n/m) - ConVerTT 13:02:49 01/19/05 Only if you're a tard... - 90Z-NA (ATL) 22:26:22 01/19/05 yeah - the past few times we got lucky and it went right - boileralum 12:29:47 01/19/05 I just started thinking about that :-) (n/m) - ConVerTT 13:04:53 01/19/05 It is OUT !!! and undamaged. - ConVerTT 12:42:44 01/19/05 Pics - Tranny out on lift - ConVerTT 13:00:02 01/19/05 What is the problem with the top two bolts? Did you - AzHeat 13:12:40 01/19/05 Well - I followed the clutch replacement FAQ but >>> - ConVerTT 13:35:51 01/19/05 That's what I did. I remove both sides of the support - AzHeat 13:53:26 01/19/05 Cool - it should go a little quicker next time now that - ConVerTT 14:19:19 01/19/05 I always lower the motor some: Even when I use a lift. (n/m) - z32ttvert 22:09:27 01/19/05 man a 36" 3/8''s extension and a 3/8's impact gun - BOOZTD 3 14:19:15 01/19/05 I'm patting myself on the back right now. (n/m) - aggiez32 15:01:45 01/19/05
Post a Followup	You cannot reply to this message because you are not logged in.