Subject	Working on these cars in general for that matter :>P (n/m)
Posted by	BrianTT(TPA,FL) on January 19, 2005 at 11:47 AM
	This message has been viewed 18 times.
In Reply To	I have a new level of respect for you guys that work posted by ConVerTT on January 19, 2005 at 11:32 AM
Message
Follow Ups	I have a new level of respect for you guys that work - ConVerTT 11:32:47 01/19/05 Thank you, thank you (bow) :) (n/m) - Haasz32 11:34:45 01/19/05 2nd (n/m) - ForceFedZ32 (SoCal) 12:11:16 01/19/05 actually, I bet the 2 bolts would be easier on the ground... - Waco300zx 11:39:10 01/19/05 Working on these cars in general for that matter :>P (n/m) - BrianTT(TPA,FL) 11:47:13 01/19/05 been there... not fun (n/m) - DragonSi 11:49:33 01/19/05 bah ... just wait til you have to get it back on :) (n/m) - Guapo 11:51:15 01/19/05 No kidding... - 90Z-NA (ATL) 11:53:44 01/19/05 ever hear of a transmission jack ? - Luke@tirerack 12:22:23 01/19/05 For those of use w/o lifts - boileralum 12:42:59 01/19/05 I have that and it works awesome. - Woody75 (Denver) 12:48:16 01/19/05 yep (n/m) - Guapo 12:51:17 01/19/05 I help PunkZ with that jack. The problem with the jack - AzHeat 13:03:56 01/19/05 put the drain in the middle of the jack, and use the belt - boileralum 16:03:29 01/19/05 I used plywood and two 2x4 nailed to each side and - AzHeat 17:08:57 01/19/05 Like I need another expense :-| (n/m) - 90Z-NA (ATL) 12:44:39 01/19/05 I am using a tranny jack also. See - even more respect - ConVerTT 12:40:56 01/19/05 Doing it w. out a tranny jack is foolish and dangerous. (n/m) - YugoBernie (NoVA) 12:56:13 01/19/05 Agreed. I worked up a pretty good sweat even with the jack (n/m) - ConVerTT 13:02:49 01/19/05 Only if you're a tard... - 90Z-NA (ATL) 22:26:22 01/19/05 yeah - the past few times we got lucky and it went right - boileralum 12:29:47 01/19/05 I just started thinking about that :-) (n/m) - ConVerTT 13:04:53 01/19/05 It is OUT !!! and undamaged. - ConVerTT 12:42:44 01/19/05 Pics - Tranny out on lift - ConVerTT 13:00:02 01/19/05 What is the problem with the top two bolts? Did you - AzHeat 13:12:40 01/19/05 Well - I followed the clutch replacement FAQ but >>> - ConVerTT 13:35:51 01/19/05 That's what I did. I remove both sides of the support - AzHeat 13:53:26 01/19/05 Cool - it should go a little quicker next time now that - ConVerTT 14:19:19 01/19/05 I always lower the motor some: Even when I use a lift. (n/m) - z32ttvert 22:09:27 01/19/05 man a 36" 3/8''s extension and a 3/8's impact gun - BOOZTD 3 14:19:15 01/19/05 I'm patting myself on the back right now. (n/m) - aggiez32 15:01:45 01/19/05
Post a Followup	You cannot reply to this message because you are not logged in.