Subject	well apparently the bolt hole on the plenum isn't "open"
Posted by	maglito on January 08, 2005 at 1:58 AM
	This message has been viewed 41 times.
In Reply To	Unfortunately I dont see how that would even work. There posted by Ash's Z on January 08, 2005 at 01:14 AM
Message	in the back, meaning you can't hook that bolt through the back of it. But, you would be tightening the nut on the outside of the thottle body in this proposed setup not "inside the plenum". Oh well, if there is no place to hook it appaently doesn't matter. I will have to modify my plenum like yours to make this work. Looking forward to your complete write up. BTW, thanks for the reply! I'm glad some people have something better to do than refresh tt.net all night. Cheers to your hard work and info sharing, keep it up!
Follow Ups	60mm Throttle Body Conversion: COMPLETE >> - Ash's Z 18:56:25 01/07/05 Very cool, can't wait for the full write-up (n/m) - DougZXTT 19:00:01 01/07/05 looks about like the others i have seen do this. (n/m) - Halo Z 19:02:45 01/07/05 Yeah, its nothing special.. Just a lot of time, mostly. (n/m) - Ash's Z 19:04:49 01/07/05 Nice work...... (n/m) - Kyle(Houston) 19:03:33 01/07/05 2nd.... (n/m) - lewoolf2 19:18:24 01/07/05 looks like lots of work. did you do any test fitting? - Boris 19:04:50 01/07/05 They come close actually. But there is about 3/16" between - Ash's Z 19:06:28 01/07/05 Didn't Z1 said that you stole the idea from them? - HakenTT 19:07:21 01/07/05 that "idea" was around longer than Z1. sorry. (n/m) - Halo Z 19:08:57 01/07/05 he also said "to h3ll with it, you only live once" recently. - whitepearlz 19:12:30 01/07/05 No comment on Z1. John Paul Beckman was the driving - Ash's Z 19:24:55 01/07/05 What were the bearing sizes - do you have much variance? (n/m) - Keith58 21:03:05 01/07/05 You mean before or after? They were all grade 3 bearings - Ash's Z 01:16:28 01/08/05 Preach on Brother Beavis. :) (I mean yeah! I'm with you Ash! (n/m) - ZFreak (Dallas) 23:13:36 01/07/05 Correction: 120 degrees between each cylinder. (n/m) - sparkie 12:16:24 01/08/05 You are correct - - Ash's Z 14:36:09 01/08/05 is that a carpeted garage floor? - MyZ8u 19:09:23 01/07/05 it looks like a linoleom floor to me. (n/m) - TwinTurboPoweredZ 19:14:56 01/07/05 No, its painted with a random pattern.. I like it though. - Ash's Z 19:29:56 01/07/05 About the dyno comparison? - Speedy1003 (IN) 20:21:23 01/07/05 with that kind of thinking, doesn't the turbo, and IC - maglito 21:12:44 01/07/05 Yes, and I wish someone would straighten me out if I'm wrong (n/m) - Speedy1003 (IN) 00:11:14 01/08/05 ash seems to be asleep for the evening or something - maglito 00:49:25 01/08/05 Been in the garage fabbing up some FMIC ducting. - Ash's Z 01:17:34 01/08/05 How would you put the hose connectors on with - TwinTurboPoweredZ 19:11:52 01/07/05 It will fit.. I just stepped out into the garage to check. (n/m) - Ash's Z 19:15:06 01/07/05 Great work Ash, you are always thinking outside the box. (n/m) - TwinTurboPoweredZ 19:15:49 01/07/05 Thanks for the support.. I can't lay claim - Ash's Z 19:56:53 01/07/05 I have 2 for myself allready - maglito 19:18:09 01/07/05 It would have been nice to find a bolt that was offset - Ash's Z 19:27:58 01/07/05 something like this (j bolt): - maglito 21:05:31 01/07/05 Unfortunately I dont see how that would even work. There - Ash's Z 01:14:15 01/08/05 well apparently the bolt hole on the plenum isn't "open" - maglito 01:58:38 01/08/05 i get what you are saying, but i think that would kinda be.. - College Boy 11:17:34 01/08/05 nEaTo Good job (n/m) - TARGETZ 19:23:17 01/07/05 how long would the next set take you? - spotz 19:41:18 01/07/05 We'll find out with my NA project engine. :) (n/m) - Ash's Z 19:50:39 01/07/05 Re: 60mm Throttle Body Conversion: COMPLETE >> - Mesa 20:36:56 01/07/05 nice job (n/m) - komplexZ(Orlando) 22:22:07 01/07/05 Cool...I'm gonna go serch the junkyards next week :) - College Boy 22:53:54 01/07/05 this mod will score NO points @ Hot Import Nights (n/m) - fourZero 23:43:50 01/07/05 You forget, show AND go. (n/m) - maglito 02:00:56 01/08/05 Very cool. (n/m) - YugoBernie (NoVA) 00:17:29 01/08/05 nice work! (n/m) - Chris(NJ) 06:41:46 01/08/05 Nice work, but I'm convinced of the benefits - sparkie 12:48:43 01/08/05 not :) (n/m) - sparkie 12:49:36 01/08/05 Even though the compressor outlet is only 2", the rest of - Ash's Z 14:31:43 01/08/05 Re: Even though the compressor outlet is only 2", the rest of - sparkie 16:57:27 01/08/05 Very nice work ( as always ) - ZBlacktt 13:59:35 01/08/05 I have a welder that will do aluminum now. :) - Ash's Z 14:33:39 01/08/05 some info on the tb's - govaardz(Aruba) 15:13:00 01/08/05 nice info, thx :) (n/m) - ZBlacktt 15:22:35 01/08/05 Good to see.. Too bad there are no flowrates for 60mm, - Ash's Z 15:47:42 01/08/05 nice (n/m) - aliaZ 18:15:03 01/08/05
Post a Followup	You cannot reply to this message because you are not logged in.