Subject	I have 2 for myself allready
Posted by	maglito on January 07, 2005 at 7:18 PM
	This message has been viewed 63 times.
In Reply To	60mm Throttle Body Conversion: COMPLETE >> posted by Ash's Z on January 07, 2005 at 06:56 PM
Message	And for those following this Chip was right they are from a early 90's stanza (2.4L) not a maxima. I was thinking, and perhaps I am plain wrong, but couldn't you almost fashion some kind of bolt-hooks around around the lower two bolt holes instead of instead of filling and tapping? If this is a really bad idea, please keep the flames to a minimum. Thanks.
Follow Ups	60mm Throttle Body Conversion: COMPLETE >> - Ash's Z 18:56:25 01/07/05 Very cool, can't wait for the full write-up (n/m) - DougZXTT 19:00:01 01/07/05 looks about like the others i have seen do this. (n/m) - Halo Z 19:02:45 01/07/05 Yeah, its nothing special.. Just a lot of time, mostly. (n/m) - Ash's Z 19:04:49 01/07/05 Nice work...... (n/m) - Kyle(Houston) 19:03:33 01/07/05 2nd.... (n/m) - lewoolf2 19:18:24 01/07/05 looks like lots of work. did you do any test fitting? - Boris 19:04:50 01/07/05 They come close actually. But there is about 3/16" between - Ash's Z 19:06:28 01/07/05 Didn't Z1 said that you stole the idea from them? - HakenTT 19:07:21 01/07/05 that "idea" was around longer than Z1. sorry. (n/m) - Halo Z 19:08:57 01/07/05 he also said "to h3ll with it, you only live once" recently. - whitepearlz 19:12:30 01/07/05 No comment on Z1. John Paul Beckman was the driving - Ash's Z 19:24:55 01/07/05 What were the bearing sizes - do you have much variance? (n/m) - Keith58 21:03:05 01/07/05 You mean before or after? They were all grade 3 bearings - Ash's Z 01:16:28 01/08/05 Preach on Brother Beavis. :) (I mean yeah! I'm with you Ash! (n/m) - ZFreak (Dallas) 23:13:36 01/07/05 Correction: 120 degrees between each cylinder. (n/m) - sparkie 12:16:24 01/08/05 You are correct - - Ash's Z 14:36:09 01/08/05 is that a carpeted garage floor? - MyZ8u 19:09:23 01/07/05 it looks like a linoleom floor to me. (n/m) - TwinTurboPoweredZ 19:14:56 01/07/05 No, its painted with a random pattern.. I like it though. - Ash's Z 19:29:56 01/07/05 About the dyno comparison? - Speedy1003 (IN) 20:21:23 01/07/05 with that kind of thinking, doesn't the turbo, and IC - maglito 21:12:44 01/07/05 Yes, and I wish someone would straighten me out if I'm wrong (n/m) - Speedy1003 (IN) 00:11:14 01/08/05 ash seems to be asleep for the evening or something - maglito 00:49:25 01/08/05 Been in the garage fabbing up some FMIC ducting. - Ash's Z 01:17:34 01/08/05 How would you put the hose connectors on with - TwinTurboPoweredZ 19:11:52 01/07/05 It will fit.. I just stepped out into the garage to check. (n/m) - Ash's Z 19:15:06 01/07/05 Great work Ash, you are always thinking outside the box. (n/m) - TwinTurboPoweredZ 19:15:49 01/07/05 Thanks for the support.. I can't lay claim - Ash's Z 19:56:53 01/07/05 I have 2 for myself allready - maglito 19:18:09 01/07/05 It would have been nice to find a bolt that was offset - Ash's Z 19:27:58 01/07/05 something like this (j bolt): - maglito 21:05:31 01/07/05 Unfortunately I dont see how that would even work. There - Ash's Z 01:14:15 01/08/05 well apparently the bolt hole on the plenum isn't "open" - maglito 01:58:38 01/08/05 i get what you are saying, but i think that would kinda be.. - College Boy 11:17:34 01/08/05 nEaTo Good job (n/m) - TARGETZ 19:23:17 01/07/05 how long would the next set take you? - spotz 19:41:18 01/07/05 We'll find out with my NA project engine. :) (n/m) - Ash's Z 19:50:39 01/07/05 Re: 60mm Throttle Body Conversion: COMPLETE >> - Mesa 20:36:56 01/07/05 nice job (n/m) - komplexZ(Orlando) 22:22:07 01/07/05 Cool...I'm gonna go serch the junkyards next week :) - College Boy 22:53:54 01/07/05 this mod will score NO points @ Hot Import Nights (n/m) - fourZero 23:43:50 01/07/05 You forget, show AND go. (n/m) - maglito 02:00:56 01/08/05 Very cool. (n/m) - YugoBernie (NoVA) 00:17:29 01/08/05 nice work! (n/m) - Chris(NJ) 06:41:46 01/08/05 Nice work, but I'm convinced of the benefits - sparkie 12:48:43 01/08/05 not :) (n/m) - sparkie 12:49:36 01/08/05 Even though the compressor outlet is only 2", the rest of - Ash's Z 14:31:43 01/08/05 Re: Even though the compressor outlet is only 2", the rest of - sparkie 16:57:27 01/08/05 Very nice work ( as always ) - ZBlacktt 13:59:35 01/08/05 I have a welder that will do aluminum now. :) - Ash's Z 14:33:39 01/08/05 some info on the tb's - govaardz(Aruba) 15:13:00 01/08/05 nice info, thx :) (n/m) - ZBlacktt 15:22:35 01/08/05 Good to see.. Too bad there are no flowrates for 60mm, - Ash's Z 15:47:42 01/08/05 nice (n/m) - aliaZ 18:15:03 01/08/05
Post a Followup	You cannot reply to this message because you are not logged in.