Subject	Re: Answers
Posted by	ni[X]it on December 29, 2004 at 2:51 PM
	This message has been viewed 107 times.
In Reply To	Question posted by xtensive on December 29, 2004 at 02:47 PM
Message	:How did you get it up on that lumber like that? Seesaw. there are two 'stackable' bases under each wheel. therefore, there are a total of eight of those things. I lift the front first and get one set under both front wheels. I move to the back and lift the rear and get all four sets under both tires. Then I go to the front again and lift the rest of the way to finish the last two. It takes very little time and the car is extremely stable. If i am doing suspension upgrades, I use the blocks on the back, and jack stands up front (or vice cersus). "As the Z32 gets older and decreases in value it becomes affordable by lower income and often less desirable people whose tastes reflect their personality and social standing.- Marshall 17:37:05 10/10/03 Petz #3
Follow Ups	up in the air - kikbak82 14:06:05 12/29/04 Good job! It gets faster and easier each time. - zxjpmzx 14:15:35 12/29/04 and another way to do it, (maybe safer too)...>>> - ni[X]it 14:21:44 12/29/04 that would make taking the exhaust off much easier - spyhunter(nj) 14:25:25 12/29/04 how would it be any different than jackstands? (n/m) - Spee 16:24:21 12/29/04 jackstands are closer to the center; less room, i guess - schuss 16:40:43 12/29/04 having dropped about 20 trannies with the car on jackstands - Spee 17:11:48 12/29/04 bingo....here is my take on it... - spyhunter(nj) 21:35:38 12/29/04 rookies :) - Spee 22:50:54 12/29/04 I was thinking of doing that, but - kikbak82 14:27:15 12/29/04 $30.oo is too expensive? WOW. - ni[X]it 14:32:36 12/29/04 It is for a college student (n/m) - kikbak82 14:58:14 12/29/04 this is how I do it.(big pic) - 90300zxtt 14:51:26 12/29/04 Your going to have a hard time getting the tranny - Spongerider :) 14:54:42 12/29/04 To high? (n/m) - 90300zxtt 14:56:22 12/29/04 You need to be higher. (n/m) - Spongerider :) 14:58:05 12/29/04 too low. - ni[X]it 14:58:51 12/29/04 2nd. I had to slide the tranny out from right behind the - zxjpmzx 14:58:56 12/29/04 Re: 2nd. I had to slide the tranny out from right behind the - 90300zxtt 15:09:15 12/29/04 Good idea. I don't have much experience with jack stands... - zxjpmzx 15:33:31 12/29/04 Do yourself a favor... - Dallas DamonZ 15:14:16 12/29/04 Re: Do yourself a favor... - ni[X]it 15:21:14 12/29/04 2nd. (not that ni[x]it needs my approval) - schuss 16:43:57 12/29/04 Jenga anyone? (n/m) - Milo (Sport Z Magazine) 14:34:42 12/29/04 Question - xtensive 14:47:55 12/29/04 Re: Answers - ni[X]it 14:51:52 12/29/04 That is what I do, I have 2 sets of ramps and I just - Unluky (MO) 14:56:39 12/29/04 I bet you did not drive it up any of the ramps in photo! - zxjpmzx 15:04:38 12/29/04 Actually I did drive up on the fronts, but then I jacked it - Unluky (MO) 16:03:14 12/29/04 OK....I lost the bet....:) (n/m) - zxjpmzx 16:13:29 12/29/04 Wow, nice roomy garage you got there! (n/m) - xtensive 15:25:10 12/29/04 Yeah, force air heat as well! It is not mine, but I helped - Unluky (MO) 16:04:47 12/29/04 I used wheel ramps and jackstands. (n/m) - PIRANHA(Go Steelers!!!) 23:24:00 12/29/04 My flying Z... - Rob'Z 16:18:56 12/29/04
Post a Followup	You cannot reply to this message because you are not logged in.