Subject	Has anyone dynoed Garrett's GT28R turbos on a TTZ...
Posted by	The_S_Man (Phoenix) on December 14, 2004 at 9:23 AM
	This message has been viewed 165 times.
Message	I have a pair of these turbos (see the specs below) and have fabricated the WG actuator brackets with HKS actuators and reclocked the intercooler pipes myself... But, I was just wondering... are there any dyno numbers for these turbos on a TTZ? Does anyone out there have this setup on a TTZ and willing to give me some information? Garrett Part Number: 466541-1 Turbo specs: GT DUAL STEEL BALLBEARING CARTRIDGE TURBINE SPECS: T25 .64 A/R Turbine Housing 62 Trim Turbine COMPRESSOR SPECS: T3 .60 A/R Housing 60 Trim Wheel Compressor Flow: 31 LB/MIN Thanks, Jamie the_s_man@juno.com
Follow Ups	Has anyone dynoed Garrett's GT28R turbos on a TTZ... - The_S_Man (Phoenix) 09:23:20 12/14/04 You are in Gilbert too, So am I. Where abouts? (n/m) - AzHeat 09:35:53 12/14/04 Re: You are in Gilbert too, So am I. Where abouts? - The_S_Man (Phoenix) 09:40:29 12/14/04 Cooper and Ray, About 3 miles from me. (n/m) - AzHeat 09:43:30 12/14/04 U've got mail!!! (n/m) - The_S_Man (Phoenix) 09:52:12 12/14/04 He helped me out with my idle :) What's happening guys? (n/m) - PunkZTT(Phoenix) 11:46:07 12/14/04 Not much... I'm ready to pull an engine 4 bigger turbos:) - The_S_Man (Phoenix) 11:55:03 12/14/04 email down? (n/m) - fourZero 11:54:26 12/14/04 0000,0000, 0000,0000, - AzHeat 12:17:28 12/14/04 legitimate question... (n/m) - Dallas DamonZ 13:39:24 12/14/04 I have them on my Z, but haven't dynoed yet. It is - boileralum 10:16:25 12/14/04 Are you happy with them??? - The_S_Man (Phoenix) 10:56:35 12/14/04 I don't think they are very laggy at all - about the same - boileralum 11:00:38 12/14/04 Also, if I were buying new turbos today instead of 2.5 - boileralum 11:04:42 12/14/04 My install went easy (n/m) - HakenTT 11:13:58 12/14/04 But your GT28R turbos should be more powerful than Sport530s - Marshall 14:31:04 12/14/04 We'll find out in a month or so when I put my car on the - boileralum 15:41:24 12/14/04 Hmmm.. That's not the GT28RS (AKA:Disco Potato) - Ash's Z 10:45:02 12/14/04 That is correct... not the Disco Potato (GT28RS). - The_S_Man (Phoenix) 10:54:01 12/14/04 Laggy is relative . Mine didn't reach full boost - AzHeat 11:06:25 12/14/04 Your turbos are overkill - HakenTT 11:13:07 12/14/04 ;) I don't think there is such a thing. (n/m) - FlawleZ (San Antonio) 11:21:00 12/14/04 We are using the same CHRA in our bigger turbos. - Chip(GMS Racing) 11:47:55 12/14/04 I believe mine is the 56 trim on the compressor. Higher - AzHeat 11:50:30 12/14/04 Wastegate is not a big deal, we are using TO4B compressor - Chip(GMS Racing) 11:54:43 12/14/04 I think they are about the same. I guess I didn't - AzHeat 12:02:04 12/14/04 Am in the valley as well. I got those - HakenTT 11:12:21 12/14/04 Did you dyno it? - Marshall 11:48:40 12/14/04 You will never see a dyno chart from HakenTT. His claims - AzHeat 15:19:56 12/14/04 Just found your post.... Thanks, it really helps. - The_S_Man (Phoenix) 11:49:55 12/14/04 He refuses to dyno to prove numbers. (n/m) - AzHeat 11:51:34 12/14/04 I will prove it but you pay for dyno (n/m) - HakenTT 14:01:36 12/14/04 maybe you can get your parents to pay for it (n/m) - aliaZ 18:55:39 12/14/04 Am sure am over 500hp with 20psi of boost - HakenTT 14:03:29 12/14/04 Is that the butt dyno proof or your omnipotence proof? (n/m) - AzHeat 15:14:23 12/14/04 I just ordered the Same turbos, How much did you get them - shawn300zTT GT28R soon 16:42:40 12/14/04 I got robbed... - The_S_Man (Phoenix) 17:06:46 12/14/04
Post a Followup	You cannot reply to this message because you are not logged in.