TwinTurbo.NET: Nissan 300ZX forum - he didn't say he saw it in the pics, just suggested that
Subject
he didn't say he saw it in the pics, just suggested that
Posted by
JokerF15 (NyxMotorsports)
on December 06, 2004 at 10:00 PM
This message has been viewed
77
times.
In Reply To
Where do you see an oil pan in the pictures???..... (n/m)
posted by Kyle(Houston)
on December 06, 2004 at 08:59 PM
Message
SpooledUpZ check out the oil pan.
-JokerF15
Follow Ups
Got my engine back from SGP...
-
SpooledUpZ
18:14:38 12/06/04
Wow i wouldn't expect that from them. (n/m)
-
MikeVar82
18:25:58 12/06/04
think mine had 2 straps, but otherwise very similar
-
spotz
18:40:04 12/06/04
wayyy too conservative (n/m)
-
shawnc
18:49:20 12/06/04
not at all on 91 octane (n/m)
-
KILLR300ZX
18:58:46 12/06/04
10k+ worth of conservative?
-
spotz
19:00:36 12/06/04
ok, thanks. I appreciate the feedback (n/m)
-
SpooledUpZ
18:52:08 12/06/04
Are you saying that you run your gt2530's at 13 psi?
-
Bernie (OOParts International)
20:31:47 12/06/04
Your going to have a very nice setup! (n/m)
-
Spongerider :)
18:43:46 12/06/04
Thanks, I cant wait! (n/m)
-
SpooledUpZ
18:52:46 12/06/04
Looks like a fairly stable position....I wouldn't sweat it.
-
RSR
18:44:04 12/06/04
You're going to enjoy that setup. I know I do =) (n/m)
-
Moxie
19:02:50 12/06/04
thanks ;) how similiar is your setup? Have you had it dyno'd
-
SpooledUpZ
19:15:46 12/06/04
It's very similar, check my profile for specifics.
-
Moxie
19:33:07 12/06/04
looks fine to me (n/m)
-
Guapo
19:16:20 12/06/04
SGP Engine = Tough cookie. I've had good experience with
-
Ash's Z
19:37:13 12/06/04
You should inspect the oil pan for dents
-
HakenTT
19:37:41 12/06/04
Ok, will do..Thanks! (n/m)
-
SpooledUpZ
20:27:27 12/06/04
Where do you see an oil pan in the pictures???..... (n/m)
-
Kyle(Houston)
20:59:01 12/06/04
he doesnt have to see it. he is omnipetent (n/m)
-
joel(PA)
21:11:25 12/06/04
he didn't say he saw it in the pics, just suggested that -
JokerF15 (NyxMotorsports)
22:00:01 12/06/04
No to burst your bubble but there is NO pan on the engine. (n/m)
-
YugoBernie (NoVA)
23:05:14 12/06/04
You should contact SGP directly.
-
Kenny
19:38:27 12/06/04
i love it when people assume...
-
SpooledUpZ
19:51:32 12/06/04
Then leave a message and wait for his response. (n/m)
-
Kenny
00:09:39 12/07/04
Ill handle it how i feel necessary, thanx (n/m)
-
SpooledUpZ
12:47:54 12/07/04
When you handle it in this fashion, you look foolish. (n/m)
-
Kenny
14:34:16 12/07/04
Because i didnt leave a message im foolish?
-
SpooledUpZ
14:54:56 12/07/04
Keep the boost 'round 15 and stock timing until you can get
-
Scotts94z32
19:54:41 12/06/04
Ok, thats what i was planning on doin. Thanks for the advice (n/m)
-
SpooledUpZ
20:03:55 12/06/04
2nd, I have a very similar set up and Keep it @13 for
-
Ghozt
23:23:57 12/06/04
Hmmmm...shipping company must have removed one strap--->
-
Kyle(Houston)
21:00:12 12/06/04
Thanks Kyle, Im sure im just being paranoid and there most
-
SpooledUpZ
21:15:38 12/06/04
NP...if there is damage let me know & I will take care of it (n/m)
-
Kyle(Houston)
21:24:19 12/06/04
Kyle, did you read my email I sent you? (n/m)
-
AzHeat
21:44:54 12/06/04
Mine did not arrive like that. (n/m)
-
Chris(NJ)
22:28:50 12/06/04
I have similar mods except I have Stillen SMICs and a SAFC.
-
myttzx
11:10:57 12/07/04
SGP Motor. Make sure you check
-
Boosted1
11:31:19 12/07/04
Post a
Followup
You cannot reply to this message because you are not
logged in
.