Subject	Are you saying that you run your gt2530's at 13 psi?
Posted by	Bernie (OOParts International) on December 06, 2004 at 8:31 PM
	This message has been viewed 105 times.
In Reply To	think mine had 2 straps, but otherwise very similar posted by spotz on December 06, 2004 at 06:40 PM
Message	Looking at your profile it looks like you have all the supporting mods to run it at higher psi. You really are missing out on all of the fun! I run 19-20 psi on 93 octane with Aquamist on my GT2530's. Without Aquamist, I'll run 17-18psi in 90+ degree Miami heat and humidity with no problems. Especially since you have a JWT ECU you have plenty of room to increase the boost safely. Bernie, U.S. sales rep for...
Follow Ups	Got my engine back from SGP... - SpooledUpZ 18:14:38 12/06/04 Wow i wouldn't expect that from them. (n/m) - MikeVar82 18:25:58 12/06/04 think mine had 2 straps, but otherwise very similar - spotz 18:40:04 12/06/04 wayyy too conservative (n/m) - shawnc 18:49:20 12/06/04 not at all on 91 octane (n/m) - KILLR300ZX 18:58:46 12/06/04 10k+ worth of conservative? - spotz 19:00:36 12/06/04 ok, thanks. I appreciate the feedback (n/m) - SpooledUpZ 18:52:08 12/06/04 Are you saying that you run your gt2530's at 13 psi? - Bernie (OOParts International) 20:31:47 12/06/04 Your going to have a very nice setup! (n/m) - Spongerider :) 18:43:46 12/06/04 Thanks, I cant wait! (n/m) - SpooledUpZ 18:52:46 12/06/04 Looks like a fairly stable position....I wouldn't sweat it. - RSR 18:44:04 12/06/04 You're going to enjoy that setup. I know I do =) (n/m) - Moxie 19:02:50 12/06/04 thanks ;) how similiar is your setup? Have you had it dyno'd - SpooledUpZ 19:15:46 12/06/04 It's very similar, check my profile for specifics. - Moxie 19:33:07 12/06/04 looks fine to me (n/m) - Guapo 19:16:20 12/06/04 SGP Engine = Tough cookie. I've had good experience with - Ash's Z 19:37:13 12/06/04 You should inspect the oil pan for dents - HakenTT 19:37:41 12/06/04 Ok, will do..Thanks! (n/m) - SpooledUpZ 20:27:27 12/06/04 Where do you see an oil pan in the pictures???..... (n/m) - Kyle(Houston) 20:59:01 12/06/04 he doesnt have to see it. he is omnipetent (n/m) - joel(PA) 21:11:25 12/06/04 he didn't say he saw it in the pics, just suggested that - JokerF15 (NyxMotorsports) 22:00:01 12/06/04 No to burst your bubble but there is NO pan on the engine. (n/m) - YugoBernie (NoVA) 23:05:14 12/06/04 You should contact SGP directly. - Kenny 19:38:27 12/06/04 i love it when people assume... - SpooledUpZ 19:51:32 12/06/04 Then leave a message and wait for his response. (n/m) - Kenny 00:09:39 12/07/04 Ill handle it how i feel necessary, thanx (n/m) - SpooledUpZ 12:47:54 12/07/04 When you handle it in this fashion, you look foolish. (n/m) - Kenny 14:34:16 12/07/04 Because i didnt leave a message im foolish? - SpooledUpZ 14:54:56 12/07/04 Keep the boost 'round 15 and stock timing until you can get - Scotts94z32 19:54:41 12/06/04 Ok, thats what i was planning on doin. Thanks for the advice (n/m) - SpooledUpZ 20:03:55 12/06/04 2nd, I have a very similar set up and Keep it @13 for - Ghozt 23:23:57 12/06/04 Hmmmm...shipping company must have removed one strap---> - Kyle(Houston) 21:00:12 12/06/04 Thanks Kyle, Im sure im just being paranoid and there most - SpooledUpZ 21:15:38 12/06/04 NP...if there is damage let me know & I will take care of it (n/m) - Kyle(Houston) 21:24:19 12/06/04 Kyle, did you read my email I sent you? (n/m) - AzHeat 21:44:54 12/06/04 Mine did not arrive like that. (n/m) - Chris(NJ) 22:28:50 12/06/04 I have similar mods except I have Stillen SMICs and a SAFC. - myttzx 11:10:57 12/07/04 SGP Motor. Make sure you check - Boosted1 11:31:19 12/07/04
Post a Followup	You cannot reply to this message because you are not logged in.