Subject	about speed density
Posted by	sparkie on November 29, 2004 at 11:32 AM
	This message has been viewed 70 times.
In Reply To	My $.02 posted by Ash's Z on November 29, 2004 at 01:56 AM
Message	speed density is: 1. more accurate than our MAF because it calculates the air flow much closer to the intake port. (speed density uses MAP reading off the intake manifold. Whereas MAF uses reading from the beginning of inake system: not accurate). 2. much faster response than OEM MAF because MAF uses hot wire to measure air flow. www.ztechz.net ICQ # 14337317
Follow Ups	Zemulator vs BrandX Standalone Debate - BOOZTD 3 23:20:13 11/28/04 The reason i stay with stock ECU's on my Z's and honda's - sweet z (UTAH) 23:37:09 11/28/04 I'll agree - BOOZTD 3 23:43:53 11/28/04 VTC Control is nice... - xybertron 23:55:38 11/28/04 Most stand alones use speed density, so the response - AzHeat 01:37:24 11/29/04 MAP would be nice... - xybertron 01:59:50 11/29/04 Map would be the best conversion for the VG motor because - AzHeat 08:26:16 11/29/04 Re: MAP would be nice... - sparkie 11:38:00 11/29/04 sure you will.. (n/m) - SniPer SR71 (Dallas) 16:06:05 11/29/04 isnt it mechanically op, not electrically operated? (n/m) - BooZted 08:01:14 11/29/04 uses a solenoid to mechanicaly operate an oil valve - AzHeat 08:22:54 11/29/04 Best argument I have seen - 16x16 resolution map - maglito 00:08:37 11/29/04 My $.02 - Ash's Z 01:56:03 11/29/04 Thanks for the read, my mind is already made up.... - BOOZTD 3 04:47:56 11/29/04 Why do you need to convince your friends? - Marshall 10:24:28 11/29/04 Both of these points i know - BOOZTD 3 17:27:31 11/29/04 LOL - Ash's Z 18:52:24 11/29/04 That was a good post Sir. (n/m) - RSR 06:47:46 11/29/04 Re: My $.02 - genic 08:46:15 11/29/04 I play the drums. :) (n/m) - Ash's Z 10:58:10 11/29/04 awesome! did you know jerry plays them as well? - genic 11:19:28 11/29/04 I've been to Georgia, I know "The Springer Effect", LOL. - Ash's Z 12:31:00 11/29/04 I play the drums. :) (n/m) - Ash's Z 12:12:26 11/29/04 two drums? (n/m) - SactoTodd 12:25:15 11/29/04 Why would speed density be less accurate than MAS? - AzHeat 11:08:11 11/29/04 It is my understanding that the temperature sensor in a - Ash's Z 12:26:38 11/29/04 Re: It is my understanding that the temperature sensor in a - sparkie 15:45:32 11/29/04 about speed density - sparkie 11:32:22 11/29/04 Here's something to think about: - Marshall 10:44:52 11/29/04 You are forgetting timing resolution - kuah@splparts.com 11:59:53 11/29/04 I'm not forgetting that. - Marshall 14:58:42 11/29/04 Re: I'm not forgetting that. - sparkie 15:34:29 11/29/04 You are way off. The ECU consists of two processors - Ash's Z 15:39:13 11/29/04 How am I way off? Did you even read my post? - Marshall 16:43:11 11/29/04 I did. Why are you getting so defensive? I only said you - Ash's Z 18:36:53 11/29/04 You are way off. The ECU consists of two processors - Ash's Z 18:35:05 11/29/04 I'm way off again? (n/m) - Marshall 20:39:48 11/29/04 Re: I'm not forgetting that. - kuah@splparts.com 18:36:20 11/29/04 If one has the need to tune down to a tenth of a degree - Ash's Z 18:44:19 11/29/04 Re: If one has the need to tune down to a tenth of a degree - kuah@splparts.com 19:24:16 11/29/04 Re: Re: If one has the need to tune down to a tenth of a degree - Marshall 22:17:41 11/29/04 yeah, I think you're right. (n/m) - Marshall 20:41:09 11/29/04
Post a Followup	You cannot reply to this message because you are not logged in.