Subject	So you support keeping them in the stock BOSE enclosure?
Posted by	PLEAZURE in CA (SD) on October 15, 2004 at 3:27 PM
	This message has been viewed 20 times.
In Reply To	If you're doing a sub, cross those dyns over at posted by twinturbineZ on October 15, 2004 at 01:42 AM
Message	Thanks for the advice about the 100hz .. I'll try that. For now I am using the 4 channels Alpine amp to run the Dynaudio speakers on the front channels, then the sub, will run on a bridged rear channels @ 4Ohm For now I am considering one JL audio 10 inch W3v2 ..dual coil with 2 Ohm each coil .. when I bridge them they will give me 4Ohm which is what my amp can handle bridged.. 45Wx4 4ohm; Bridged (0.3% THD) 90Wx2 .. here are the specs for the amp La-Z-Link Let me know if I got the sub set up right ... "It should come as no surprise that the people who own and control the world have put their interests before the greater good of humanity." Henry Makow Ph.D. PLEAZURE in SD The trouble with doing something right the first time is that nobody appreciates how difficult it was. Matt 91TT Aztec Red stg IV+
Follow Ups	After customizing my front enclosures to fit 6.5" speakers - PLEAZURE in CA (SD) 00:13:53 10/14/04 Seal that up with some Dynamat and crimp or solder some - twinturbineZ 00:16:24 10/14/04 looks like someone needs a dremel. (n/m) - Rage (SoCal) 00:17:43 10/14/04 Hehe .. you are so correct .. (n/m) - PLEAZURE in CA (SD) 00:19:48 10/14/04 You had better wrap those XOVERS up or MOVE them - twinturbineZ 00:18:26 10/14/04 Where do you suggest I mount them, not too many options in Z - PLEAZURE in CA (SD) 00:21:49 10/14/04 You really shouldn't put them in the door at all, however - twinturbineZ 00:24:45 10/14/04 I mounted mine behind the seats with the amps. (n/m) - manstretch (NC) 00:28:40 10/14/04 Instructions says that the wire between the crossover - PLEAZURE in CA (SD) 00:31:25 10/14/04 Well, I was running all new speaker anyways, plus I couldn't - manstretch (NC) 00:33:55 10/14/04 Believe me, If you mounted them behind the seat or in the - twinturbineZ 00:34:02 10/14/04 OH, and wrap some grille cloth around those tweeters - twinturbineZ 00:27:43 10/14/04 What happened to not wanting to spend $$$ on speakers? :) - SeedyROM 00:40:54 10/14/04 I told my story before, I went to the stereo shop and listen - PLEAZURE in CA (SD) 00:46:17 10/14/04 If you want them to sound anywhere near as good as they - twinturbineZ 00:50:42 10/14/04 Indeed - SeedyROM 00:56:17 10/14/04 Nice, I hadn't seen that post - SeedyROM 00:51:43 10/14/04 Dude, if you afford Dynaudios, get the OEM metal brackets - shirow 00:56:34 10/14/04 One says bracket, one says enclosure ! can I get an answer - PLEAZURE in CA (SD) 02:38:33 10/14/04 I put in Infinity's, here's what I did - dpjax 06:40:08 10/14/04 Thanks, but I think using bare wires in not scientifically - PLEAZURE in CA (SD) 12:45:10 10/14/04 You're right, but also bare wire tends to oxidize and - twinturbineZ 00:28:02 10/15/04 Sorry Matt, I didn't read your post carefully enough. But I - shirow 13:36:15 10/14/04 I have my crossovers in the front doors. No problems at all - jkeyser14 09:07:59 10/14/04 The Bose enclosures do not have enough airspace for - Dan (Vancouver) 16:28:32 10/14/04 Thanks guys for your input .. I will just cut the back of - PLEAZURE in CA (SD) 18:51:08 10/14/04 Are you installing a sub as well? What amp are you using on - twinturbineZ 20:23:19 10/14/04 Re: Are you installing a sub as well? What amp are you using on - PLEAZURE in CA (SD) 22:47:27 10/14/04 If you're doing a sub, cross those dyns over at - twinturbineZ 01:42:15 10/15/04 So you support keeping them in the stock BOSE enclosure? - PLEAZURE in CA (SD) 15:27:48 10/15/04
Post a Followup	You cannot reply to this message because you are not logged in.