Subject	band saw if you want a clean cut, any steel fabricating>>>
Posted by	CAP927(Boston) on October 13, 2004 at 7:51 AM
	This message has been viewed 26 times.
In Reply To	How would you cut an engine block in half? posted by Dallas DamonZ on October 12, 2004 at 10:52 PM
Message	place would have a big enough saw to make a single even cut any way you would want it. If you decide to cut it with a torch it will take a bit more time since you need to make several cuts just to get to the middle as you mentioned, but it can be done. You just need the right amount of heat and the right tip. Or a plasma cutter, but again only steel fabricators or a steel erecting company would have a tool able to cut that thickness. Grandma was right... It IS what's on the inside that counts!
Follow Ups	How would you cut an engine block in half? - Dallas DamonZ 22:52:39 10/12/04 Plasma cutter maybe? (n/m) - ImTheDevil 22:58:05 10/12/04 d'oh! (n/m) - Guapo 22:58:26 10/12/04 lol, 3 sec - ImTheDevil 23:01:55 10/12/04 How far can those cut? - Dallas DamonZ 23:04:28 10/12/04 upon further review, they're for thinner materials (n/m) - Guapo 23:06:58 10/12/04 <1 inch for practical applications... - Snoguitar 23:07:48 10/12/04 mine will sever 1.5" steel - T0M 17:40:13 10/13/04 plasma cutter? (n/m) - Guapo 22:58:08 10/12/04 Big band-saw? (n/m) - Snoguitar 22:58:11 10/12/04 2nd probably easiest too (n/m) - Ron(Houston) 23:22:14 10/12/04 3rd... - dbotos 14:10:33 10/13/04 guillotine (n/m) - Chris(NJ) 22:58:35 10/12/04 friggin laser (n/m) - red300zxtt 23:02:09 10/12/04 on a shark? (n/m) - Dallas DamonZ 23:05:11 10/12/04 dammit, i jusy shot milk out my nose. OUChhhh.. thanks,D. (n/m) - Halo Z 23:43:46 10/12/04 great, now Damon has milk on his butt. (n/m) - Rage (SoCal) 23:55:57 10/12/04 as long as it's only milk.... (n/m) - Dallas DamonZ 00:04:01 10/13/04 ghey.... (n/m) - Halo Z 01:55:51 10/13/04 LMAO (n/m) - JRH(KY) 07:36:09 10/13/04 I see my old block is going to be put to good use. - punkz (Dallas) 23:04:55 10/12/04 Re: I see my old block is going to be put to good use. - Dallas DamonZ 23:06:08 10/12/04 four banger sig? come on now (n/m) - College Boy 23:06:36 10/12/04 i thought of that, too. but i don't want 300 lb furniture.. - schuss 00:18:14 10/13/04 Full engines work way better than just half - College Boy 23:05:23 10/12/04 water jet...? (n/m) - Tu 23:08:23 10/12/04 2nd (n/m) - Mighty-Znoobie 23:43:21 10/12/04 3rd...Water jet will cut up to 8 inches... heres links - FireMedicZ 00:35:30 10/13/04 kindergarders safety scissors? (n/m) - ENVYMYZ 23:20:30 10/12/04 you could give this guy a call... - Spee 23:38:03 10/12/04 just don't ask this guy. luke did, and got his hand - maxboost83 00:41:04 10/13/04 band saw is the only thing that will get your deep enough - halik 01:48:23 10/13/04 band saw if you want a clean cut, any steel fabricating>>> - CAP927(Boston) 07:51:20 10/13/04 I believe a German hacksaw would work. - Riddick 09:21:32 10/13/04 Goldfinger's crotch-burning LASER -- "can project a spot on - Z-Jay (Edmonton, AB) 09:46:08 10/13/04 I would personally use my own laser eyes, but for mortals - RSR 09:50:53 10/13/04 Kill an Alien and let its acid blood drip over the block (n/m) - kandy2dr 10:17:19 10/13/04
Post a Followup	You cannot reply to this message because you are not logged in.