Subject	You may still be warping them but...
Posted by	KaZ (VaBch) on September 24, 2004 at 2:03 PM
	This message has been viewed 29 times.
In Reply To	Kaz, thanks for the info so far, i have another question posted by mousersix (San Antonio) on September 24, 2004 at 01:42 PM
Message	Its hard to believe you've warped so many... Are you doing proper break in? What pads are you using? What rotors? Have you had an alignment done lately? What about a tire balance? KaZ (VaBch) - "Unique Z" Back to the crap '84 S12 CA18ET Silvia '88 Z31 VG30E Fairlady Z - Beater '91 Z32 [ Project ] Fairlady Z '97 A32 VQ30DE Cefiro AIM - KaZsMiR / E-mail @ Hotmail - casimijg "Forumers are like economists: They state the obvious, give bad advice, and simply can't agree with each other." - Someone Else
Follow Ups	DAMN wrapped rotors.... again :>( Ok guys >>>> - BrianTT(TPA,FL) 12:06:42 09/23/04 wrapped in what? tin foil? (n/m) - craziestbob 12:07:49 09/23/04 unwrap them, re-install, and you're good to go (n/m) - hey GotBo0st 12:10:26 09/23/04 are you sure? (n/m) - Halo Z 12:10:27 09/23/04 How many lbs do you torque your lug nuts? (n/m) - Spongerider :) 12:10:50 09/23/04 *crap (n/m) - Southern_Z [IL] 12:12:26 09/23/04 rap fool - joel(PA) 12:14:48 09/23/04 red 'x' fool (n/m) - U ZCREAM 12:16:05 09/23/04 RaP FooL - joel(PA) 12:16:09 09/23/04 3rd time's a charm (n/m) - Z32Nizzan 12:16:41 09/23/04 lol (n/m) - craziestbob 12:19:52 09/23/04 Flava Flave iz n da houze (n/m) - myzislow 12:21:47 09/23/04 flavaaaaaaaa flavvvvvvvvv (n/m) - Tissan. 12:23:16 09/23/04 werd G (n/m) - Rage (SoCal) 12:24:47 09/23/04 omg, falling out of chair, ha ha! (n/m) - Jonezy 12:24:48 09/23/04 wait a minute, you're not Jonezy! (n/m) - hey GotBo0st 12:27:13 09/23/04 last time i checked i was... (n/m) - Jonezy 12:30:14 09/23/04 watch the movie Dreamcatcher (n/m) - hey GotBo0st 12:32:30 09/23/04 that one is a fake i promise :P (n/m) - Jonezy 12:35:19 09/23/04 Is this you? - Z32Nizzan 12:36:07 09/23/04 I'm the REAL Jonezy!!!!! He's a fake! (n/m) - Jonezy 12:46:34 09/23/04 yeah, he's real. i know him.... no faker here.... (n/m) - Halo Z 12:54:22 09/23/04 I was just quoting the movie, u guys took this way too far (n/m) - hey GotBo0st 12:55:37 09/23/04 Halo to the rescue :P (n/m) - Jonezy 12:57:31 09/23/04 shhh it would ruin my rep. (n/m) - Halo Z 13:18:05 09/23/04 heh. (n/m) - Rage (SoCal) 12:36:02 09/23/04 I Duditz! (n/m) - Spee 13:52:24 09/23/04 glad somebody saw it (n/m) - hey GotBo0st 20:05:46 09/23/04 I saw it, but I'm not glad. - Spee 23:11:30 09/23/04 worst movie...EVER - HalfnHalf702[HJC] 11:55:30 09/24/04 nah, that award goes to From Dusk til Dawn... - Spee 13:40:30 09/24/04 i dunno, house of 1000 corpses was pretty lame too (n/m) - HalfnHalf702[HAZ] 14:36:20 09/24/04 never saw it... - Spee 01:22:31 09/25/04 Read this - PiotrC70 12:16:17 09/23/04 Not saying their wrong, just take that with a grain of salt. - SooperZ95 12:48:45 09/23/04 you sure its your disks?? - Ted(Snowflake Customs) 12:46:21 09/23/04 do solid tension rods provide for a smoother ride - mousersix (San Antonio) 13:13:55 09/23/04 Not really a smoother ride, but they'll stop shudder during - KaZ (VaBch) 13:53:11 09/23/04 Kaz, thanks for the info so far, i have another question - mousersix (San Antonio) 13:42:12 09/24/04 You may still be warping them but... - KaZ (VaBch) 14:03:44 09/24/04 stock brakes, dont know what pads, havent needed to - mousersix (San Antonio) 14:13:42 09/24/04 If you don't know what pads you're using, you might want to - KaZ (VaBch) 14:24:55 09/24/04 yea, i was planning on a complete brake rebuild soon - mousersix (San Antonio) 14:34:20 09/24/04 Give them a scrub with a fine sandpaper - ZEngineer (TT) 12:54:06 09/23/04 I doubt the problem is the rotors. (n/m) - YugoBernie (NoVA) 12:59:44 09/23/04 Care to elaborate a little bit for the guy - Evan(CA) 14:31:59 09/23/04 Not really, here is why. - YugoBernie (NoVA) 15:15:04 09/23/04 2nd (n/m) - Spee 23:12:34 09/23/04 rebuild your calipers. see faq!!!!!!!!!!!1111 (n/m) - Carlo$-91NA-2+2-5$p 14:24:01 09/23/04 get bigger rotors OR - yellowzxtt 14:42:22 09/23/04 What brand or rotors do you have? - Chip(GMS Racing) 18:48:20 09/23/04
Post a Followup	You cannot reply to this message because you are not logged in.