Subject	Cause I was told that the crimp is so good the wire will
Posted by	ZisLuv on September 23, 2004 at 6:24 AM
	This message has been viewed 21 times.
In Reply To	Why would you think crimping is better than soldering? posted by AzHeat on September 22, 2004 at 02:04 PM
Message	snap before the crimp would come apart from it, hence I couldnt see how soldering it would be better. Plus if there was a wiring error then to switch it around its just a matter of unplugging and switching to the right pin. If its soldered it you would have to unsolder and resolder again being much more time consuming. They were my thoughts anyway.
Follow Ups	Motec screenshots (lots of pics) - ZisLuv 08:49:56 09/22/04 too many pictures...jeeze! - College Boy 08:52:01 09/22/04 lol i warned you. Lots of menus. (n/m) - ZisLuv 09:03:00 09/22/04 Nice very nice - HKS 2835 09:00:14 09/22/04 how much wiring work was involved? (n/m) - joel(PA) 09:34:41 09/22/04 Re: how much wiring work was involved? - HKS 2835 09:40:29 09/22/04 nothing too hard, just need to cut the existing loom - ZisLuv 09:45:43 09/22/04 30 minutes? - sparkie 09:52:01 09/22/04 cut wire, crimp connector, plug in and repeat - ZisLuv 09:58:18 09/22/04 Crimp connectors suck....to get a more accurate reading -> - jkperformance 09:59:16 09/22/04 how is soldering better than a properly crimped connector? (n/m) - ZisLuv 10:03:57 09/22/04 Re: how is soldering better than a properly crimped connector? - sparkie 10:12:13 09/22/04 ah ic. Not sure what these are like. - ZisLuv 10:18:12 09/22/04 crimp connects come loose fairly often. they can create a - jkperformance 10:14:00 09/22/04 Re: cut wire, crimp connector, plug in and repeat - sparkie 10:03:25 09/22/04 why is that, thought itd be the other way around? (n/m) - ZisLuv 10:04:56 09/22/04 Re: why is that, thought itd be the other way around? - sparkie 10:15:09 09/22/04 Looks really good! I would take Sparkie's advise - Spongerider :) 12:06:26 09/22/04 Why would you think crimping is better than soldering? - AzHeat 14:04:32 09/22/04 Cause I was told that the crimp is so good the wire will - ZisLuv 06:24:44 09/23/04 nice setup, too bad it is so expensive- - E_swift 10:34:24 09/22/04 yeah not cheap, i guess close to 4-5kUS installed - ZisLuv 10:44:13 09/22/04 Why? Zemulator is cheap, easy to use, and easy to install... - Borg79(ON) 13:03:12 09/22/04 Re: Why? Zemulator is cheap, easy to use, and easy to install... - Spongerider :) 15:40:09 09/22/04 Yeah but thats just getting a number on a dyno chart - ZisLuv 06:35:43 09/23/04 Danger to Manifold!!!!!!! (n/m) - kandy2dr 15:17:28 09/22/04
Post a Followup	You cannot reply to this message because you are not logged in.