Subject	Then I accept your challenge! j/k :)
Posted by	Zoltan on August 10, 2004 at 12:55 PM
	This message has been viewed 21 times.
In Reply To	i challenge you to now make it your life's mission. :) (n/m) posted by BoostLesZ on August 10, 2004 at 12:47 PM
Message	I actually have a friend who knows how to weld in aluminum. He said that I could try it and see if it holds/melts.
Follow Ups	Why not make an aluminum exhaust? - Zoltan 12:30:11 08/10/04 because... - BoostLesZ 12:36:17 08/10/04 Re: because... - Zoltan 12:38:38 08/10/04 Yeah, $$$$$$ - KaZ (VaBch) 12:47:09 08/10/04 i challenge you to now make it your life's mission. :) (n/m) - BoostLesZ 12:47:54 08/10/04 Then I accept your challenge! j/k :) - Zoltan 12:55:33 08/10/04 good luck, batman! - BoostLesZ 13:03:37 08/10/04 Aluminum can be welded. There are limitations to the - Scotts94z32 12:56:28 08/10/04 smartass (n/m) - ZEngineer (TT) 12:59:08 08/10/04 What about titanium? - Chaaarmndr (NoVa) 13:17:18 08/10/04 Titanium is $$$$$$$$$$$$$$$$ (n/m) - Z-Jay (Edmonton, AB) 13:21:45 08/10/04 Very true. (n/m) - Chaaarmndr (NoVa) 13:25:31 08/10/04 I was thinking Wolfram... do you know what that is? :) (n/m) - Scotts94z32 14:02:22 08/10/04 it's tungsten and it is super heavy! (n/m) - Technomancer 14:10:06 08/10/04 ding! I actually know a guy who has Wolfram as his CA plate. - Scotts94z32 14:20:19 08/10/04 I have some darts made from Tungsten. Good stuff. (n/m) - boileralum 15:40:54 08/10/04 Yup - Spiff187( Calgary,AB ) 13:23:08 08/10/04 and I think Penthouse makes one for the Z... not sure though (n/m) - Spiff187( Calgary,AB ) 13:24:02 08/10/04 And Hustler makes intakes... (n/m) - ZEngineer (TT) 13:25:53 08/10/04 Witty george, just witty (n/m) - Chaaarmndr (NoVa) 13:26:25 08/10/04 I learned from the best (n/m) - ZEngineer (TT) 13:27:22 08/10/04 lol. the more you post, the more i like canadians. :) (n/m) - BoostLesZ 13:28:47 08/10/04 *scanning for sarcasm*........It's clean! - ZEngineer (TT) 13:30:29 08/10/04 Holy poop! I hadn't seen your car since before the paint - Kez43 13:57:37 08/10/04 Thanks, here's the original post: - ZEngineer (TT) 14:03:15 08/10/04 Pentroof??? (n/m) - Chaaarmndr (NoVa) 13:26:02 08/10/04 S#1t, I'm tired =( sorry yeah (n/m) - Spiff187( Calgary,AB ) 13:26:52 08/10/04 Where cost is a non-issue, titanium and Ti-alloys are God- - Scotts94z32 13:33:17 08/10/04 is your z lower in the front than it is in the rear? - mousersix (San Antonio) 14:14:00 08/10/04 Nope... just the angle of that pic... 18x9s all around, with - Scotts94z32 14:21:24 08/10/04 there arent really any limitations on aluminum thicknesses. - T0M 14:25:32 08/10/04 here are several reasons - yellowzxtt 13:27:49 08/10/04
Post a Followup	You cannot reply to this message because you are not logged in.