TwinTurbo.NET: Nissan 300ZX forum - I have 285/35/18s on 18x10 rears w/ no rubbing (n/m)
Subject
I have 285/35/18s on 18x10 rears w/ no rubbing (n/m)
Posted by
boileralum
on August 04, 2004 at 6:23 PM
This message has been viewed
29
times.
In Reply To
what tire size? (n/m)
posted by eroc77
on August 04, 2004 at 01:52 PM
Message
Follow Ups
whats the largest wheel width and tire set up for the z? (n/m)
-
eroc77
13:47:53 08/04/04
You can fit 10s in the rear,9s in the front. 18" tall is
-
YugoBernie (NoVA)
13:49:31 08/04/04
what tire size? (n/m)
-
eroc77
13:52:23 08/04/04
i have 275/35 bfg drag radials on a 18"x10" wheel (n/m)
-
myzislow
13:54:42 08/04/04
SCC reported 285 w/inner fender roll! (n/m)
-
eroc77
13:57:14 08/04/04
SO! Why are you asking! why are you excited! (n/m)
-
Tennyson (ATL)
13:59:03 08/04/04
lol (n/m)
-
tommunist
14:06:30 08/04/04
easy! was just wondering if anyone has installed them! (n/m)
-
eroc77
14:08:33 08/04/04
you could have asked "has anyone installed 285s"! (n/m)
-
SactoTodd
14:15:33 08/04/04
LOL, nice touch! (n/m)
-
Tennyson (ATL)
14:16:46 08/04/04
eroc77 aka. Tony Little
-
Tennyson (ATL)
14:16:00 08/04/04
my bad! new at this....has anyone
-
eroc77
14:17:32 08/04/04
Anything possible with a hacksaw and some glue (n/m)
-
SimplyZ
14:23:55 08/04/04
Has anyone what? tony!
-
Tennyson (ATL)
14:34:53 08/04/04
well how long have you been on this forum?
-
eroc77
14:40:01 08/04/04
Where's homeland security when you need them? (n/m)
-
SimplyZ
14:45:12 08/04/04
!!! (n/m)
-
Tennyson (ATL)
14:52:37 08/04/04
I have 285/35/18s on 18x10 rears w/ no rubbing (n/m) -
boileralum
18:23:43 08/04/04
I installed a 19x10.5 with a 295 in the rear with no issues
-
Luke@tirerack
14:29:37 08/04/04
Luke...what tire size should I go with i just got 18x10.5
-
RotaZ
14:52:26 08/04/04
what offset is the wheel (n/m)
-
Luke@tirerack
14:54:19 08/04/04
Could you please answer my email re:
-
VECTOR
18:17:19 08/04/04
ROFL! (n/m)
-
Z-Jay (Edmonton, AB)
15:57:12 08/04/04
255 & 285 YOKO. AVS SPORTS ON VOLK RACING GTA 17s (n/m)
-
greenmachine
17:50:52 08/04/04
Post a
Followup
You cannot reply to this message because you are not
logged in
.