Subject	Those are meant to go in the engine bay and not in the cabin
Posted by	SeedyROM on July 07, 2004 at 3:09 AM
	This message has been viewed 40 times.
In Reply To	Just pick up the B&M Fuel Pressure gauge,Need mounting ideas posted by dusthis on July 07, 2004 at 02:28 AM
Message	You see many of them right at the fuel filter on cars. I mean, it can be plumbed to the cabin but because it is not electronic with a remote sensor, you'll be plumbing fuel directly into the cabin which isn't recommended unless your car is a full blown racecar. I wouldn't do it. My 300Zs: www.zheaven.com - Have a question about either of my 300ZXs? Answers lie within. Admin: www.350ZForum.com - Your source for the lastest info on the new Nissan 350Z! Writer: www.SportZMagazine.com - Nothing but Z cars from cover to cover! Subscribe today! Moderator: www.TwinTurbo.net - Hands down, the best site for 90-96 Z car info and discussion!
Follow Ups	Just pick up the B&M Fuel Pressure gauge,Need mounting ideas - dusthis 02:28:50 07/07/04 i wish i could give you a great idea - Red ZX (SoCal) 03:07:22 07/07/04 Thanks,Kinda what I was thinking.NE danger of possible - dusthis 03:13:40 07/07/04 no fuel lines should go into the cabin... - spyhunter(nj) 06:31:29 07/07/04 Those are meant to go in the engine bay and not in the cabin - SeedyROM 03:09:15 07/07/04 FWIW, my fathers 67 Fastback burned to the ground because - SeedyROM 03:15:20 07/07/04 Ya burning up a car with no insurance is never any fun - dusthis 03:17:38 07/07/04 mechanical fuel pressure gauge mounting location... - dbotos 03:17:14 07/07/04 Cool just what I was looking for! What readings do you - dusthis 03:21:34 07/07/04 see bottom of this page... - dbotos 03:43:10 07/07/04 Good show (n/m) - SeedyROM 03:21:57 07/07/04 and you know what... - Red ZX (SoCal) 03:30:54 07/07/04 you can get a 0-100 psi electric w/ sender for <$80... - dbotos 03:36:51 07/07/04 Very nice. BTW- Your missing a bolt on your coilpack. (n/m) - Milo (Sport Z Magazine) 09:29:11 07/07/04 thanks... - dbotos 14:19:11 07/07/04 on the hood? it'd be cool if it was done right. (n/m) - turbosailor(trans. to Seattle) 07:15:28 07/07/04 Highly recommended that you don't mout it in the - whitepearlz 07:28:01 07/07/04 If you use SS braided line.... - RAGTPZ(OH) 08:28:42 07/07/04 Where did you get the strut tower cover? - govaardz(Aruba) 10:21:03 07/07/04 No doubt - SeedyROM 11:26:07 07/07/04 you should see his cool struts bolts he has now also (n/m) - PLEAZURE in CA (SD) 12:20:11 07/07/04 got those off ebay for like $7, getting one custom fabbed - RAGTPZ(OH) 13:29:14 07/07/04 Cool I fabbed some in Aluminum a while ago (n/m) - govaardz(Aruba) 14:13:50 07/07/04
Post a Followup	You cannot reply to this message because you are not logged in.