Subject	You do not have to pull the crank to replace the oil pump.
Posted by	boileralum on May 05, 2004 at 2:35 PM
	This message has been viewed 39 times.
In Reply To	Ummm no, thats not what were talkin bout... posted by Zluster(Project Aardvark) on May 05, 2004 at 11:08 AM
Message	The pump slides onto the end of the crank. Rule #1 - There's always a bastard! JRH(KY): for some reason, when I hear the word 'tranny' I think of transvestite before I do transmission. don't ask me why boileralum: FAGMO! ----------------------------------------- Bill (ImTheDevil): blah blah blah me: Just because you are covered in gasoline right now, doesn't mean you are right!
Follow Ups	Hey everyone Quick Q - fst300zx 01:56:29 05/05/04 Good luck - NytWolf 01:58:36 05/05/04 well.... - fst300zx 02:19:38 05/05/04 did this guy also leave on the Timin Belt when he did this? (n/m) - Zluster(Project Aardvark) 02:21:23 05/05/04 god i hope not cause thats impossible.. (n/m) - fst300zx 02:23:58 05/05/04 no. should just disconnect oil cooler lines and undo all the - ScubaSteve 11:04:21 05/05/04 Ummm no, thats not what were talkin bout... - Zluster(Project Aardvark) 11:08:26 05/05/04 i thought you were talking oil pan, all i saw was - ScubaSteve 11:31:00 05/05/04 You do not have to pull the crank to replace the oil pump. - boileralum 14:35:01 05/05/04 ohhh, you mean after pulling the underdrive pulley and - ScubaSteve 17:26:59 05/05/04 ya after pulling the crank and everthing...... - Zluster(Project Aardvark) 21:47:16 05/05/04 Dropping the subframe WITH the hoist there is going to be - KaZ (VaBch) 07:40:36 05/05/04 someone was talkin about doing that to replace a spun bearin - Zluster(Project Aardvark) 02:05:08 05/05/04 You've gotta be kidding - NytWolf 02:14:54 05/05/04 Dont ask me... - Zluster(Project Aardvark) 02:19:41 05/05/04 Seems like Chivas tried to do that. Don't remember... - JRH(KY) 07:34:30 05/05/04 Done it on an NA, support the engine, lower the subframe - DJG(MI) 08:10:08 05/05/04 but thats weight on the crank..sounds bad - fst300zx 10:45:32 05/05/04 No, I put the jackstand under the transmission bellhousing- - DJG(MI) 08:05:24 05/06/04 This guy did it in the tech section...with a decently - BigTDogg (MA) 09:30:59 05/05/04 kaizer mags on "the toys," eh? - E_swift (molmolmolmol) 10:07:26 05/05/04 well they are owned by Florida Tech - fst300zx 10:15:19 05/05/04 yeah, i checked the FT site - E_swift (molmolmolmol) 16:17:22 05/05/04 well they are owned by Florida Tech - fst300zx 10:40:03 05/05/04
Post a Followup	You cannot reply to this message because you are not logged in.