Subject	Dropping the subframe WITH the hoist there is going to be
Posted by	KaZ (VaBch) on May 05, 2004 at 7:40 AM
	This message has been viewed 27 times.
In Reply To	well.... posted by fst300zx on May 05, 2004 at 02:19 AM
Message	A BITCH... What you really want to do is get a BRACE, basically a thick bar with feet that you can place over the engine in the engine bay, then strap the engine to that. Then remove the subframe from below... Having the feet of the hoist under the car is going to be a HUGE pain in the ass. KaZ (VaBch) - "Unique Z" '84 S12 CA18ET Silvia '88 Z31 VG30E Fairlady Z - Beater '91 Z32 [ Removed ] Fairlady Z - Version S [ Personal ] '91 Z32 [ Reconstruction ] Fairlady Z - Version S [ Project ] '97 A32 VQ30DE Cefiro SE AIM - KaZsMiR / E-mail @ Hotmail - casimijg "Forumers are like economists: They state the obvious, give bad advice, and simply can't agree with each other." - Someone Else
Follow Ups	Hey everyone Quick Q - fst300zx 01:56:29 05/05/04 Good luck - NytWolf 01:58:36 05/05/04 well.... - fst300zx 02:19:38 05/05/04 did this guy also leave on the Timin Belt when he did this? (n/m) - Zluster(Project Aardvark) 02:21:23 05/05/04 god i hope not cause thats impossible.. (n/m) - fst300zx 02:23:58 05/05/04 no. should just disconnect oil cooler lines and undo all the - ScubaSteve 11:04:21 05/05/04 Ummm no, thats not what were talkin bout... - Zluster(Project Aardvark) 11:08:26 05/05/04 i thought you were talking oil pan, all i saw was - ScubaSteve 11:31:00 05/05/04 You do not have to pull the crank to replace the oil pump. - boileralum 14:35:01 05/05/04 ohhh, you mean after pulling the underdrive pulley and - ScubaSteve 17:26:59 05/05/04 ya after pulling the crank and everthing...... - Zluster(Project Aardvark) 21:47:16 05/05/04 Dropping the subframe WITH the hoist there is going to be - KaZ (VaBch) 07:40:36 05/05/04 someone was talkin about doing that to replace a spun bearin - Zluster(Project Aardvark) 02:05:08 05/05/04 You've gotta be kidding - NytWolf 02:14:54 05/05/04 Dont ask me... - Zluster(Project Aardvark) 02:19:41 05/05/04 Seems like Chivas tried to do that. Don't remember... - JRH(KY) 07:34:30 05/05/04 Done it on an NA, support the engine, lower the subframe - DJG(MI) 08:10:08 05/05/04 but thats weight on the crank..sounds bad - fst300zx 10:45:32 05/05/04 No, I put the jackstand under the transmission bellhousing- - DJG(MI) 08:05:24 05/06/04 This guy did it in the tech section...with a decently - BigTDogg (MA) 09:30:59 05/05/04 kaizer mags on "the toys," eh? - E_swift (molmolmolmol) 10:07:26 05/05/04 well they are owned by Florida Tech - fst300zx 10:15:19 05/05/04 yeah, i checked the FT site - E_swift (molmolmolmol) 16:17:22 05/05/04 well they are owned by Florida Tech - fst300zx 10:40:03 05/05/04
Post a Followup	You cannot reply to this message because you are not logged in.