Subject	well....
Posted by	fst300zx on May 05, 2004 at 2:19 AM
	This message has been viewed 59 times.
In Reply To	Good luck posted by NytWolf on May 05, 2004 at 01:58 AM
Message	I talked it over with some friends in Gainsville and they said i would have to hoist the motor up then drop the subframe and proceed to pull all the bolts untill the pan comes off. There are two oil passages going to the turbos and i think thats about it. I also found out that you can do this without removing the tranny and exhaust. Anyways, I dont think I have enough balls to start this project. This was from a buddy who swapped his oil pump with the motor in the car... and that just sounds crazy. ~matt~ been a member ever since i owned my 1st 300zx i love twinturbo.net thanks guys
Follow Ups	Hey everyone Quick Q - fst300zx 01:56:29 05/05/04 Good luck - NytWolf 01:58:36 05/05/04 well.... - fst300zx 02:19:38 05/05/04 did this guy also leave on the Timin Belt when he did this? (n/m) - Zluster(Project Aardvark) 02:21:23 05/05/04 god i hope not cause thats impossible.. (n/m) - fst300zx 02:23:58 05/05/04 no. should just disconnect oil cooler lines and undo all the - ScubaSteve 11:04:21 05/05/04 Ummm no, thats not what were talkin bout... - Zluster(Project Aardvark) 11:08:26 05/05/04 i thought you were talking oil pan, all i saw was - ScubaSteve 11:31:00 05/05/04 You do not have to pull the crank to replace the oil pump. - boileralum 14:35:01 05/05/04 ohhh, you mean after pulling the underdrive pulley and - ScubaSteve 17:26:59 05/05/04 ya after pulling the crank and everthing...... - Zluster(Project Aardvark) 21:47:16 05/05/04 Dropping the subframe WITH the hoist there is going to be - KaZ (VaBch) 07:40:36 05/05/04 someone was talkin about doing that to replace a spun bearin - Zluster(Project Aardvark) 02:05:08 05/05/04 You've gotta be kidding - NytWolf 02:14:54 05/05/04 Dont ask me... - Zluster(Project Aardvark) 02:19:41 05/05/04 Seems like Chivas tried to do that. Don't remember... - JRH(KY) 07:34:30 05/05/04 Done it on an NA, support the engine, lower the subframe - DJG(MI) 08:10:08 05/05/04 but thats weight on the crank..sounds bad - fst300zx 10:45:32 05/05/04 No, I put the jackstand under the transmission bellhousing- - DJG(MI) 08:05:24 05/06/04 This guy did it in the tech section...with a decently - BigTDogg (MA) 09:30:59 05/05/04 kaizer mags on "the toys," eh? - E_swift (molmolmolmol) 10:07:26 05/05/04 well they are owned by Florida Tech - fst300zx 10:15:19 05/05/04 yeah, i checked the FT site - E_swift (molmolmolmol) 16:17:22 05/05/04 well they are owned by Florida Tech - fst300zx 10:40:03 05/05/04
Post a Followup	You cannot reply to this message because you are not logged in.