Subject	Some answers to your small issues
Posted by	Carlos Ramirez on April 23, 2004 at 7:04 AM
	This message has been viewed 88 times.
In Reply To	Single throttle body plenum. posted by T0M on April 22, 2004 at 11:40 PM
Message	1) Run the cima valve covers should give you mounting points for your coil packs. 2) use a catch can 3) Weld a plate to the intake and then tap that for your vacuum line fittings. If you could make the upper and lower intake manifold into once piece your can get it fit under the hood :-) Great work on getting something accomplished.
Follow Ups	Single throttle body plenum. - T0M 23:40:53 04/22/04 well so far the hood wont fit and the car wont run - Tennyson (ATL) 23:46:32 04/22/04 Hey, be a dick about it. (n/m) - Jackie 00:49:12 04/23/04 not a dick, just pointing out the obvious - Tennyson (ATL) 01:18:55 04/23/04 - Inferiority complex. - Jackie 14:28:52 04/23/04 baby steps... gotta start some place. - ni[X]it 23:48:28 04/22/04 Bypass the PCV's w/ an oil catch can and breather filters (n/m) - PunkZTT(Phoenix) 00:01:02 04/23/04 well the egr, pcv, and vacuum tees are all a matter - T0M 00:19:26 04/23/04 **VERY good answer**. You get 1,000 points :) - ni[X]it 00:21:15 04/23/04 :) (n/m) - T0M 00:24:24 04/23/04 cut a chunk out of the stock plenum where the aac and aic - ScubaSteve 12:38:29 04/23/04 there's also the EGR to keep in mind. - Zeus 23:51:45 04/22/04 they probably arent candidates for this then. (n/m) - Chris(NJ) 07:17:44 04/23/04 that's what I was thinking..sacrifices would need to be made (n/m) - Zeus 08:44:39 04/23/04 cool (n/m) - michaelkih (Dallas) 00:04:24 04/23/04 I think it looks great, who cares if it doesn't fit... - Nismootc 00:11:39 04/23/04 nice fab. job...but what would the benefit be of a single TB - Plan Z 00:13:43 04/23/04 space saving is a toss up (n/m) - Nismootc 00:15:07 04/23/04 easier for a single turbo setup (n/m) - PunkZTT(Phoenix) 00:15:16 04/23/04 Plenty in theory. - ni[X]it 00:20:44 04/23/04 i think that it would be better. It would simplify the - masashi_z32 00:55:28 04/23/04 you could always weld brackets to it for the coil packs.. - PunkZTT(Phoenix) 00:14:42 04/23/04 yeah but thats not a real fix. kinda ghetto. - T0M 00:24:02 04/23/04 Is it a split design internally? The firing order of - AzHeat 00:27:04 04/23/04 firing order is 1-2-3-4-5-6. those tricky bastards @ nissan. (n/m) - Plan Z 00:34:31 04/23/04 its internally one chamber. no tricks inside. - T0M 00:41:36 04/23/04 Are you going to do dyno and egt testing to make - AzHeat 01:00:26 04/23/04 2nd (n/m) - Waco300zx 01:08:33 04/23/04 Yes, definately plan on dynoing it soon. (n/m) - T0M 01:26:34 04/23/04 Correct plenum volume should take car of that. (n/m) - Chip(GMS Racing) 13:23:36 04/23/04 What is the plenum volume ? (n/m) - AzHeat 00:28:26 04/23/04 If you can make it fit under the stock hood and have all - mpbond(STL) 00:53:41 04/23/04 THAT will never happen. (n/m) - YugoBernie (NoVA) 01:08:45 04/23/04 I can dream can't I? (n/m) - mpbond(STL) 01:19:58 04/23/04 yeah I dont know how likely it fitting under the stock hood. - T0M 01:24:46 04/23/04 dump the egr and pcv's. Solves 2/3's of your request. (n/m) - Chris(NJ) 07:17:22 04/23/04 My car is a daily driver and has to pass emissions. There - mpbond(STL) 14:44:49 04/23/04 dumping PCV's is a bad idea - aliaZ 00:47:36 04/24/04 keep us updated man. that looks cool as hell (n/m) - Pure-Evil 01:05:56 04/23/04 Yeah DUDE! RAD! (n/m) - Tennyson (ATL) 01:17:08 04/23/04 I'm down for trying new things. Good luck man (n/m) - SeedyROM (ZCON 2K4!) 02:18:12 04/23/04 Looks great! Keep up the great innovative designing. (n/m) - RotaZ 02:58:47 04/23/04 I am in............. (n/m) - Bigplansnocar (UTAH) 04:23:47 04/23/04 Some answers to your small issues - Carlos Ramirez 07:04:09 04/23/04 ohhh i have some of those!! - Halo Z 08:20:53 04/23/04 Or you can do this... - Russ ZTT (Jax, Fl) 09:01:18 04/23/04 thats what I was thinking is to re wire our coil packs - T0M 09:25:35 04/23/04 Excellent advice. (n/m) - Kenny 09:38:42 04/23/04 yes, ill take one! - Roo 09:38:42 04/23/04 would like to add.... - Roo 10:51:11 04/23/04 I'll take one if it fits under the hood - sparkie 10:22:58 04/23/04 Very nice i would be interested too (n/m) - MikeVar82 11:31:15 04/23/04 looks great...glad to see someone working on it - mrbc80 11:44:06 04/23/04 As far as the hood issues go - dlaw300z(Austin) 13:13:33 04/23/04
Post a Followup	You cannot reply to this message because you are not logged in.