Subject	Bottom end done and almost finished with build
Posted by	SpeedyTTZ on March 06, 2004 at 7:36 PM
	This message has been viewed 480 times.
Message	Well I recieved an email from Rich at RZT today with a pic of my new motor all done from the machine shop. I am very excited to get this under way. Rich has been a good friend to me in these last few months. I want to thank him on his efforts so far. But this motor has gone through some tough times since its been in the car. My mods on this motor for now are as follows: Wiseco Pistons 88mm 8.5:1 w/ upgraded Orings Eagle Rods High Performance Main and Crank Bearings Motor bored .40 over All cast flashings bored and smoothed All rotating assemblies balanced PE1420 turbos Greg Dupree 2.5 5bolt Downpipes Greg Dupree 2.5 Test Pipes Apollo FMIC 3" JWT Dual POP JWT 740cc program JWT Mild Cams Nismo 740cc injectors Koyo Radiator Slimline electric fan UR Under Drive pulley Prototype Race Heads *1mm oversized intake valves *1mm oversized exaust valves *Titanium retainers *Upgraded vavle guides *Dual Coil Springs *Ported Exhaust manifolds Ported and matched Lower intake manifold extruded and honed Plenum extruded and honed TBs Bored Fidanza Flywheel RPS 6puck Clutch HKS Carbon Ti Exhaust HKS Hardpipes HKS EVC IV EZ Full Line of Defi gauges BF Series Border Gauge pod (Frogger) LHD version NOS direct port wet kit (shot yet TBD) Nismo Adjustable FPR Motor has all new gaskets Carbon Fiber Rad Guide SAFC Conzult Stillen Oil Cooler Kit Dual MAF setup Preluber Water Injection Heres the pic of the motor frest out of the machine shop. i have a question about TD05s-hot90tt(underconstruction) i got $5 says u fuck this up too - Wagz ------------------------------------------------------------ "Long story short my boost guage was off i think a couple psi and then the bulb went out on it that night. So I used a flashlight to read what my boost was. Looked like 19 pounds, but I guess I was wrong. Then to top it off, I was bouncing off the rev limiter and powershifted to third. And then the big boom. To my amazement, the next morning it acutlly started!!!! then I shut it off a couple secs later it was killing me to hear what it sounded like." - Posted by: hot90tt(underconstruction) on January 19, 2004 at 11:15 AM
Follow Ups	Bottom end done and almost finished with build - SpeedyTTZ 19:36:57 03/06/04 if i may be so bold - what kind of budget is this on? (n/m) - dpjax 20:27:49 03/06/04 Re: if i may be so bold - what kind of budget is this on? - SpeedyTTZ 20:54:53 03/06/04 whats up with your intercooler you talked about on 3zclub? - T0M 20:35:59 03/06/04 he went with the FMIC - mds2004 20:52:29 03/06/04 Re: whats up with your intercooler you talked about on 3zclub? - SpeedyTTZ 20:57:09 03/06/04 hmm you engine is like my twin.. I hope you didn't - Carlos Ramirez 20:42:37 03/06/04 Re: hmm you engine is like my twin.. I hope you didn't - SpeedyTTZ 20:53:07 03/06/04 Very nice.think you will have it together for the ECZA meet? (n/m) - Pats300zx 06:37:26 03/07/04 I sure do... - SpeedyTTZ 07:34:03 03/07/04
Post a Followup	You cannot reply to this message because you are not logged in.