Subject	I see what you're saying, but not having seen a two piece
Posted by	Dave N on February 17, 2004 at 12:22 PM
	This message has been viewed 61 times.
In Reply To	Re: The theory behind putting a spacer on top and bottom posted by kuah@splparts.com on February 17, 2004 at 10:58 AM
Message	set I'm shooting in the dark on this: What size would the upper spacer be? If I recall, the rubber that is at the top of the bushing is about 4 mm thick - is it safe to assume that the upper spacer be the same thickness? But at the same time, I didn't see Greg saying it was a bad thing for the frame to move up. In contrast, this may be why he didn't do a 2 piece bushing set. Anyway, thanks for setting me straight. Dave N. Sig Quotes: "Or he's having a rough week like the rest of us and decided to take out his agressions of not being breast fed on me." BigTDogg 15:45, 09/25/03 "Pick her up from day care and take her to Dairy Queen for a snow cone." YugoBernie 1/7/04 of course those are canadian bannings and beatings, which after the conversion rate is really only a "hey! stop that!" Chris(NJ) 1/14/04
Follow Ups	Greg Dupree Subframe Spacers. - MoneyPit 00:47:10 02/17/04 sh!t ya...one of the cheapest mods you can do - Red ZX (SoCal) 00:49:24 02/17/04 One word...yes (n/m) - michaelkih 00:50:38 02/17/04 Re: Greg Dupree Subframe Spacers. - MoneyPit 00:54:23 02/17/04 It helps but here is my side of story - HakenTT 00:58:50 02/17/04 Thankfully out of 2000+ pieces, only a few have leaked - SeedyROM (ZCON 2K4!) 01:05:47 02/17/04 2000+ pieces = 4 pcs per set so only 500 sets? :-) (n/m) - TARGETZ 06:25:25 02/17/04 Would the ES bushing kit be a better purchase than - DbestiZ1 08:04:55 02/17/04 My opinion is that if you do the full bushings - RSR 08:52:15 02/17/04 or the 300degree aluminum bushings (n/m) - Guapo 08:53:25 02/17/04 Yes, thanks, shoulda mentioned....... (n/m) - RSR 09:44:02 02/17/04 I wish 300degree would offer Delrin version too - TARGETZ 11:15:53 02/17/04 300Deg. doesn't usually reinvent the wheel and make - YugoBernie (NoVA) 12:07:09 02/17/04 why not get the aluminum ones? (n/m) - Spee 13:58:37 02/17/04 Dont want aluminum ones. - TARGETZ 19:53:17 02/17/04 pansy (n/m) - Spee 13:56:51 02/18/04 Re: Would the ES bushing kit be a better purchase than - SL103 12:02:22 02/17/04 Here is my experience. I use to have my original bushings - Glenn (San Jose) 01:35:47 02/17/04 Let me know how the car feels with the spacers and urethanes - SeedyROM (ZCON 2K4!) 02:37:24 02/17/04 The theory behind putting a spacer on top and bottom - Dave N 06:57:07 02/17/04 Re: The theory behind putting a spacer on top and bottom - kuah@splparts.com 10:58:16 02/17/04 I see what you're saying, but not having seen a two piece - Dave N 12:22:42 02/17/04 The 2 piece units are about 1/2 as thick each as Greg's. (n/m) - YugoBernie (NoVA) 13:31:14 02/17/04 Pic > - kuah@splparts.com 15:56:12 02/17/04 Yes it does - it locks the SF in a more neutral location. (n/m) - YugoBernie (NoVA) 12:03:34 02/17/04 Actually............ - Greg D. (Specialty-Z) 10:51:00 02/17/04 Re: Actually............ - kuah@splparts.com 11:44:21 02/17/04 Agreed..... - Greg D. (Specialty-Z) 12:34:15 02/17/04 They're well worth the money you spend on them. (n/m) - vitaminz 01:33:28 02/17/04 the spacers completely eliminated my wheel hop, but - robo (sebring1970) 05:13:41 02/17/04 yes. - felixx23 (DFW) 06:59:39 02/17/04 I got them and i absolutely love them! - shawn300zTT 07:50:51 02/17/04 best upgrade under $100... !!! go 4 it! (n/m) - Ali 08:13:43 02/17/04 Elimiating flex at the subframe mounts makes a huge - RSR 08:55:30 02/17/04 I have them, but didn't notice a difference TBQH *shrug* (n/m) - Scotts94z32 10:04:37 02/17/04 absolutely (n/m) - Spee 13:57:01 02/17/04 A huge difference in how 'buttoned down' the rear feels - Dan (Vancouver) 23:25:21 02/17/04
Post a Followup	You cannot reply to this message because you are not logged in.