Subject	Oh and yes I have *seen* it---->
Posted by	Kyle(Houston) on January 17, 2004 at 10:22 PM
	This message has been viewed 61 times.
In Reply To	Our experience was quite a bit different than yours... posted by AshsZ on January 17, 2004 at 09:53 PM
Message	We have redone 2 motors with Wiseco pistons that had pretty bad piston noise. One was due to the fact that some of the pistons were installed in the wrong direction and the other had bad tolerences that we had to use another block and start from stratch to fix. But both have no noise now. Kyle "Grumpy Bear" Puckett Sales@sgpracing.com
Follow Ups	Wiseco Piston "Noise" - Onyx Z32 15:02:12 01/17/04 If there is LOTS of slap: - therinL 15:10:45 01/17/04 Because your Wiseco pistons are built to our design. =) - AshsZ 15:22:15 01/17/04 So non-Z1 spec Wiseco's will make some noise? (n/m) - Onyx Z32 15:24:17 01/17/04 yeah, ash found the flaw in their design... (n/m) - joel(PA) 15:34:47 01/17/04 But will that flaw hurt the motor? Or just cause noise? (n/m) - Onyx Z32 15:36:45 01/17/04 Weird...we have used their pistons since 2002 w/no problems. (n/m) - Kyle(Houston) 16:21:36 01/17/04 Our customers weren't happy with the noise they made - AshsZ 18:01:53 01/17/04 Hmmm...maybe the ovaling is because you don't use----> - Kyle(Houston) 21:16:48 01/17/04 Our experience was quite a bit different than yours... - AshsZ 21:53:20 01/17/04 Nope...for real...I have talked to Brian and the head---> - Kyle(Houston) 22:11:54 01/17/04 Oh and yes I have *seen* it----> - Kyle(Houston) 22:22:26 01/17/04 Our experience was quite a bit different than yours... - AshsZ 01:51:58 01/18/04 I already answered this statement-----> - Kyle(Houston) 10:15:02 01/18/04 im not sure, but i have heard it once even with my JE's and - joel(PA) 17:07:34 01/17/04 It's not the kind of sound you would hear just once (n/m) - Good2Zya 17:29:34 01/17/04 hmm... motor was sputtering and trying to stall out - joel(PA) 17:55:49 01/17/04 if the motor was built correctly then no..... - richk 17:29:33 01/17/04 Wisecos "STOCK" spec piston properly installed - Good2Zya 15:37:49 01/17/04 :-/ They do. We've installed them in a large number of - AshsZ 18:04:49 01/17/04 No. It's people who listened to wiseco about boring.. - nixit 16:01:43 01/17/04 The early design wiseco's had .008 taper on the skirt - MikeH(Twin GT35BB Incon Z) 16:29:13 01/17/04 whatever. I have Endyn pistons (made by Wiseco) - nixit 18:08:19 01/17/04 You aren't worreid because they have the proper taper? (n/m) - MikeH(Twin GT35BB Incon Z) 18:10:45 01/17/04 Endyn has their own design of the piston, Wiseco is the - AshsZ 18:17:32 01/17/04 Endyns have less taper then standard Wiseco's. (n/m) - ni[X]it 20:21:33 01/17/04 And you know this how? (n/m) - MikeH(Twin GT35BB Incon Z) 22:20:21 01/17/04 :shrug: "I stayed at a Holiday Inn last night" (n/m) - ni[X]it 22:29:57 01/17/04 Yea, figures. Just conjecture. You didn't measure - MikeH(Twin GT35BB Incon Z) 23:11:10 01/17/04 ROFLMAO...this coming from someone who doesn't even----> - Kyle(Houston) 10:21:24 01/18/04 Thanks for the clicky, Wiseco/Nutter sent me the - MikeH(Twin GT35BB Incon Z) 12:18:42 01/18/04 So you think 87.5mm is *oversized* and bigger then 89mm???? - Kyle(Houston) 12:54:52 01/18/04 The 87.5mm label could be designated minimum bore size not - MikeH(Twin GT35BB Incon Z) 14:14:53 01/18/04 Dude Label is a label. Just like sport 500 turbos is label - MikeH(Twin GT35BB Incon Z) 14:16:40 01/18/04 Please stop.... (n/m) - Kyle(Houston) 18:09:31 01/18/04 Please top being ass yourself. (n/m) - MikeH(Twin GT35BB Incon Z) 20:08:42 01/18/04 because I told him so - aliaZ 23:13:40 01/17/04 Less taper than what? The new Wiseco's have half the - MikeH(Twin GT35BB Incon Z) 23:19:43 01/17/04 use your brain please - aliaZ 17:30:31 01/18/04 That's what wiseco did. They are using the new taper - MikeH(Twin GT35BB Incon Z) 20:10:42 01/18/04 Ultimate Z installed them. I should call them or... - Onyx Z32 15:22:52 01/17/04 When I go to check out the car, I'll take some Video... - Onyx Z32 23:40:58 01/17/04 In the middle of the problem... - Tozzz 12:25:26 01/18/04
Post a Followup	You cannot reply to this message because you are not logged in.