Subject	If there is LOTS of slap:
Posted by	therinL on January 17, 2004 at 3:10 PM
	This message has been viewed 60 times.
In Reply To	Wiseco Piston "Noise" posted by Onyx Z32 on January 17, 2004 at 03:02 PM
Message	Its possible the pistons were installed the wrong direction. For a while Wiseco was not labeling their pistons...Talk to Z1, but I think this will eventually cause engine failure... My Wiseco pistons dont ever have any slap...perfectly quiet.
Follow Ups	Wiseco Piston "Noise" - Onyx Z32 15:02:12 01/17/04 If there is LOTS of slap: - therinL 15:10:45 01/17/04 Because your Wiseco pistons are built to our design. =) - AshsZ 15:22:15 01/17/04 So non-Z1 spec Wiseco's will make some noise? (n/m) - Onyx Z32 15:24:17 01/17/04 yeah, ash found the flaw in their design... (n/m) - joel(PA) 15:34:47 01/17/04 But will that flaw hurt the motor? Or just cause noise? (n/m) - Onyx Z32 15:36:45 01/17/04 Weird...we have used their pistons since 2002 w/no problems. (n/m) - Kyle(Houston) 16:21:36 01/17/04 Our customers weren't happy with the noise they made - AshsZ 18:01:53 01/17/04 Hmmm...maybe the ovaling is because you don't use----> - Kyle(Houston) 21:16:48 01/17/04 Our experience was quite a bit different than yours... - AshsZ 21:53:20 01/17/04 Nope...for real...I have talked to Brian and the head---> - Kyle(Houston) 22:11:54 01/17/04 Oh and yes I have *seen* it----> - Kyle(Houston) 22:22:26 01/17/04 Our experience was quite a bit different than yours... - AshsZ 01:51:58 01/18/04 I already answered this statement-----> - Kyle(Houston) 10:15:02 01/18/04 im not sure, but i have heard it once even with my JE's and - joel(PA) 17:07:34 01/17/04 It's not the kind of sound you would hear just once (n/m) - Good2Zya 17:29:34 01/17/04 hmm... motor was sputtering and trying to stall out - joel(PA) 17:55:49 01/17/04 if the motor was built correctly then no..... - richk 17:29:33 01/17/04 Wisecos "STOCK" spec piston properly installed - Good2Zya 15:37:49 01/17/04 :-/ They do. We've installed them in a large number of - AshsZ 18:04:49 01/17/04 No. It's people who listened to wiseco about boring.. - nixit 16:01:43 01/17/04 The early design wiseco's had .008 taper on the skirt - MikeH(Twin GT35BB Incon Z) 16:29:13 01/17/04 whatever. I have Endyn pistons (made by Wiseco) - nixit 18:08:19 01/17/04 You aren't worreid because they have the proper taper? (n/m) - MikeH(Twin GT35BB Incon Z) 18:10:45 01/17/04 Endyn has their own design of the piston, Wiseco is the - AshsZ 18:17:32 01/17/04 Endyns have less taper then standard Wiseco's. (n/m) - ni[X]it 20:21:33 01/17/04 And you know this how? (n/m) - MikeH(Twin GT35BB Incon Z) 22:20:21 01/17/04 :shrug: "I stayed at a Holiday Inn last night" (n/m) - ni[X]it 22:29:57 01/17/04 Yea, figures. Just conjecture. You didn't measure - MikeH(Twin GT35BB Incon Z) 23:11:10 01/17/04 ROFLMAO...this coming from someone who doesn't even----> - Kyle(Houston) 10:21:24 01/18/04 Thanks for the clicky, Wiseco/Nutter sent me the - MikeH(Twin GT35BB Incon Z) 12:18:42 01/18/04 So you think 87.5mm is *oversized* and bigger then 89mm???? - Kyle(Houston) 12:54:52 01/18/04 The 87.5mm label could be designated minimum bore size not - MikeH(Twin GT35BB Incon Z) 14:14:53 01/18/04 Dude Label is a label. Just like sport 500 turbos is label - MikeH(Twin GT35BB Incon Z) 14:16:40 01/18/04 Please stop.... (n/m) - Kyle(Houston) 18:09:31 01/18/04 Please top being ass yourself. (n/m) - MikeH(Twin GT35BB Incon Z) 20:08:42 01/18/04 because I told him so - aliaZ 23:13:40 01/17/04 Less taper than what? The new Wiseco's have half the - MikeH(Twin GT35BB Incon Z) 23:19:43 01/17/04 use your brain please - aliaZ 17:30:31 01/18/04 That's what wiseco did. They are using the new taper - MikeH(Twin GT35BB Incon Z) 20:10:42 01/18/04 Ultimate Z installed them. I should call them or... - Onyx Z32 15:22:52 01/17/04 When I go to check out the car, I'll take some Video... - Onyx Z32 23:40:58 01/17/04 In the middle of the problem... - Tozzz 12:25:26 01/18/04
Post a Followup	You cannot reply to this message because you are not logged in.