Subject	Re: New Labree installed (Sound Clip Inside)
Posted by	Greg D. (Specialty-Z) on January 13, 2004 at 12:13 AM
	This message has been viewed 183 times.
In Reply To	New Labree installed (Sound Clip Inside) posted by OpticalZ on January 12, 2004 at 11:50 PM
Message	Looks Good :) We leave extra room in the bolt holes to adjust for the slight differences in different cars. The Cat-Backs are actually built on a car to try to get the fit as perfect as possible also. I have found that when installing the same system on 2 different cars they fit slightly different. The drivers side being slightly higher is easily fixed by bending the very rear bracket that hols the rubber hangers. Grab the very end of the bracket (the farthest outside edge) and pull down firmly untill you feel it move. This is easy to do in the air on a lift......It will probably require some strength with the car sitting on the ground.
Follow Ups	New Labree installed (Sound Clip Inside) - OpticalZ 23:50:15 01/12/04 sounds good, hope to get those someday (n/m) - Schoch(92TT) 00:01:47 01/13/04 I really like the Labree dual tip... - rave 00:04:59 01/13/04 Should have been able to bend it - SeedyROM (ZCON 2K4!) 00:08:17 01/13/04 Re: New Labree installed (Sound Clip Inside) - Greg D. (Specialty-Z) 00:13:25 01/13/04 Ok thanks for info Greg, ill try it again next weekend (n/m) - OpticalZ 00:16:35 01/13/04 haven't seen an update on your site about the oval tips - alcky 00:19:45 01/13/04 We are working on a dual oval tip ...... - Greg D. (Specialty-Z) 00:30:12 01/13/04 like B&B quad oval? =) - zboost 07:03:14 01/13/04 have you broken ground on the new shop yet? (n/m) - fourZero 00:23:10 01/13/04 Still looking for an Honest contractor that has time :/ (n/m) - Greg D. (Specialty-Z) 00:31:02 01/13/04 LOL....Honest & contractor don't belong in the same sentence (n/m) - Kyle(Houston) 08:42:26 01/13/04 I agree, but I am not the same. - Stealth021 11:41:06 01/13/04 OT: I might be able to help you Greg. - Stealth021 11:38:57 01/13/04 nice :-D (n/m) - alcky 00:15:16 01/13/04 go to a muffler shop... - naZeer (Houston) 00:16:29 01/13/04 Beauuutiful... (n/m) - infamouseb (NYC) 00:17:02 01/13/04 Looks good Doug! Greg recommended reclocking the - shirow 00:18:00 01/13/04 But that was if the bending didn't work. (n/m) - shirow 00:32:19 01/13/04 Thanks, ya i think ill try the bending first. (n/m) - OpticalZ 00:33:36 01/13/04 This is true too...... - Greg D. (Specialty-Z) 00:37:21 01/13/04 Looks and sounds very nice! (n/m) - Spee 01:05:26 01/13/04 Looks Great/Sounds Great! Thanks for the clip (n/m) - abailey269 01:23:55 01/13/04 It's time to PAY for your REGISTRATION - FantasyZ 01:25:50 01/13/04 Sigh, should have let it warm up first:( (n/m) - BOOZTD 3 01:47:29 01/13/04 looks great.....sounds great......is great! (n/m) - Wagz 01:57:37 01/13/04 looks good, and sounds really good. nice job :) (n/m) - komplexZ 08:20:37 01/13/04 May have been mentioned already, but here is my .02 - kickboxr99 08:45:04 01/13/04 My Labree does the exact same thing on the right side.... - Shift_(ATL) 10:24:35 01/13/04 sounds great! nice job. (n/m) - max240 10:58:44 01/13/04
Post a Followup	You cannot reply to this message because you are not logged in.