Subject	Are you using an NVSRAM?
Posted by	xtensive on December 13, 2003 at 2:13 PM
	This message has been viewed 93 times.
In Reply To	There are much better ways to do it. posted by AshsZ on December 13, 2003 at 01:52 PM
Message	You really don't have to answer any of this if you don't want to. I am curious, but I also understand you have a product to sell. If you are using NVSRAM all you need is a 74HC00 Quad NAND logic chip to act as an address decoder, a few de-coupling capacitors, a 100u Capacitor to perform the write to flash on power down, and a latch into the serial code to send a high signal to pin A15 (8000h=10000h) of the 6303 MC that is tied into the WE pin of the SRAM chip. (Basically set a write flag, instead of the read flags the stock routine sets) This should allow writing to memory at will, and very stable, not to mention FAST. Leverage the built-in serial routine that Consult uses for data aquisition, traces, etc. and eliminate the emulator. Mike
Follow Ups	The Zemulator has arrived... installed and running... - SUPRMANZ 11:16:50 12/13/03 You bought a Zemulator for your N/A? - TARGETZ 11:31:23 12/13/03 He's going to put turbos on the NA engine I built for him - AshsZ 11:33:33 12/13/03 ahh ok he didnt have anything mentioned - TARGETZ 11:43:06 12/13/03 the Z is a constant work in progress :) (n/m) - SUPRMANZ 11:44:45 12/13/03 Can the Zemualtor write to an emprom and read emproms? (n/m) - MikeH(Twin GT35BB Incon Z) 12:35:50 12/13/03 It doesnt need to. It uses an emulator to act like the - AshsZ 12:47:03 12/13/03 yea, but once I get to my final tune will the Zemulator - MikeH(Twin GT35BB Incon Z) 12:59:40 12/13/03 You can save and load any of your programs. You dont have - AshsZ 13:07:43 12/13/03 You didn't answer my question , will the Zemulator allow - MikeH(Twin GT35BB Incon Z) 13:16:41 12/13/03 Its not an eprom programmer. That method is old-school. - AshsZ 13:24:53 12/13/03 You answered my question, The Zemulator can't burn or - MikeH(Twin GT35BB Incon Z) 13:31:53 12/13/03 =) I thought I answered that question way back for you Mike. - AshsZ 13:42:12 12/13/03 No beef, I just wanted straight answer yes or no - MikeH(Twin GT35BB Incon Z) 13:55:40 12/13/03 Why are you wanting to be able to burn chips? - AshsZ 14:04:15 12/13/03 Not getting in the chip burning business if that is what - MikeH(Twin GT35BB Incon Z) 14:51:09 12/13/03 I don't need the marketing fluff, I want straight answers. - MikeH(Twin GT35BB Incon Z) 15:20:38 12/13/03 all you had to do was read what he typed. - Spee 15:43:50 12/13/03 Spee the current version does't support multiple programs - MikeH(Twin GT35BB Incon Z) 16:08:46 12/13/03 There are emulators with built in burners. Others you can - MikeH(Twin GT35BB Incon Z) 16:20:54 12/13/03 Spee do you have a Zemulator yourself? I wasn't looking - MikeH(Twin GT35BB Incon Z) 16:24:27 12/13/03 why 3 posts? - Spee 16:58:54 12/13/03 Because I think in Binary . Not Fuzzy logic. (n/m) - MikeH(Twin GT35BB Incon Z) 17:10:57 12/13/03 Why did it take him three posts to say - MikeH(Twin GT35BB Incon Z) 17:13:50 12/13/03 mangos to papayas - SactoTodd 17:34:57 12/13/03 The ZEM is designed to be installed and left in the car. (n/m) - AshsZ 13:11:02 12/13/03 You're running off an emulator all of the time??? (n/m) - xtensive 13:21:18 12/13/03 Flash memory, actually. (n/m) - AshsZ 13:34:30 12/13/03 Just curious - xtensive 13:41:22 12/13/03 There are much better ways to do it. - AshsZ 13:52:49 12/13/03 Are you using an NVSRAM? - xtensive 14:13:25 12/13/03 Sounds like you know what you're doing. - AshsZ 14:21:19 12/13/03 You have a lot more Z's to play with too! :-) (n/m) - xtensive 14:26:12 12/13/03 In other words "UH!" (n/m) - MikeH(Twin GT35BB Incon Z) 15:25:42 12/13/03 holy crap - Spee 15:45:58 12/13/03 The end product is much simpler.. - AshsZ 16:02:50 12/13/03 yeah, I understand most of that stuff... - Spee 17:01:01 12/13/03 Damn! I was thinking the same thing lol:) - DVDBURN (MD) 15:02:45 12/13/03 Actually i bought it so I could "TT" my NA. And it's a lot.. - SUPRMANZ 11:44:05 12/13/03
Post a Followup	You cannot reply to this message because you are not logged in.