Subject	Well this is good then =)
Posted by	kryptonite729 on December 08, 2003 at 4:17 PM
	This message has been viewed 58 times.
In Reply To	If we only had a 1/4 mile track 20 minutes from us, posted by AshsZ on December 08, 2003 at 04:01 PM
Message	I'm glad its wanting you to come because i do want to see some High HP Zcars run and that it comes from the south makes it that much better. And as far as the track 20min, i'm sure we both have to drive the same distance to steele. Its all back roads from my house and it takes roughly 1hr 15min at 80mph. But one day we will see each other there. unless we have to wait until reynolds again
Follow Ups	'The Peacemaker'. A few interesting pics >>>> - AshsZ 13:51:59 12/08/03 WOW... That is amazing... Congrats (n/m) - infamouseb (NYC) 13:55:53 12/08/03 deezammm!!!!!! - Jodecy 13:57:35 12/08/03 crack is whack... - dbotos 17:45:05 12/08/03 hey I resent that.. - MaxBoostTT 17:54:33 12/08/03 some amazing stuff happening down there! good work guys! (n/m) - Wagz 13:58:04 12/08/03 When I think 35 psi, I think tire pressure. Impressive. (n/m) - Kenny 14 psi 14:01:43 12/08/03 Ok, now thats a setup I could use in my rig. - E_swift (molmolmolmol) 14:01:47 12/08/03 Yes, I've always wondered how nice it would be to dump - SpeedyZX 14:43:56 12/08/03 I'd be up for it, I just don't have enough TT expertise to - E_swift (molmolmolmol) 19:59:03 12/08/03 Nice! (n/m) - Marshall 14:02:44 12/08/03 I like how a lot of the cars you build have a clean firewall - KILLR300ZX 14:04:50 12/08/03 If you are spliting the welds you have one of two things---> - Kyle(Houston) 14:14:00 12/08/03 It has to do with the design. 90 degree welds are subject - AshsZ 14:18:05 12/08/03 More like a bad welder or metal plating that is too thin---> - Kyle(Houston) 14:26:00 12/08/03 Perhaps.. We'll let Bell worry about that.. (n/m) - AshsZ 14:47:34 12/08/03 I can't even imagine driving that thing at the strip (n/m) - jkeyser14 14:17:12 12/08/03 Good numbers as far as HP goes, but how useable is it? - JayTTZ 14:20:16 12/08/03 my thoughts exactly - David 280Z 14:24:42 12/08/03 Dyno queen. (n/m) - 1991TT 14:27:39 12/08/03 very streetable - GO 14:38:53 12/08/03 Do you have a roll cage in there? (n/m) - Arnel(Z32racing.com) 14:40:47 12/08/03 Its a completely different powerband! The engine will - AshsZ 14:49:29 12/08/03 he was talking about daily driving (n/m) - David 280Z 15:08:59 12/08/03 Let Chip drive it! (n/m) - Maximamike 14:25:23 12/08/03 That'll be the day... - Scotts94z32 15:19:38 12/08/03 I do not take it personal - Chip(GMS Racing) 15:38:41 12/08/03 You're a good man. Personally, I respect what you are doing - Scotts94z32 16:09:33 12/08/03 You werent being any ruder than he was. - T0M 16:59:04 12/08/03 It was pretty funny.. =) (n/m) - AshsZ 11:06:56 12/09/03 It isn't like that. - Russell@Z1 17:50:15 12/08/03 I wouldn't think single digits yet but - kryptonite729 14:33:59 12/08/03 Not true..we ran 10.3@135 with only a little over 600rwhp--> - Kyle(Houston) 15:12:08 12/08/03 Brad talks to Patrick almost daily. We are trying to get - Chip(GMS Racing) 15:16:46 12/08/03 I think brad mentioned he couldn't get it out of the - kryptonite729 15:17:34 12/08/03 If we only had a 1/4 mile track 20 minutes from us, - AshsZ 16:01:43 12/08/03 Well this is good then =) - kryptonite729 16:17:18 12/08/03 Well, I was referring to the Birmingham bunch.. (n/m) - AshsZ 17:25:18 12/08/03 It is about an hour drive for us also. (n/m) - Chip(GMS Racing) 17:47:39 12/08/03 Re: I think brad mentioned he couldn't get it out of the - Russell@Z1 18:05:58 12/08/03 I'm ***really*** interested to see 1320 numbers. (n/m) - RSR 14:34:30 12/08/03 That's gonna be a scary ride to the 330' mark. (n/m) - Arnel(Z32racing.com) 14:39:11 12/08/03 Re: 'The Peacemaker'. A few interesting pics >>>> - ZHOUND 14:46:37 12/08/03 Way to go! Can't wait to see it when Gary gets it back here - Nissan of Wichita 15:38:26 12/08/03 Wow, I really like the install on the Profec B - JonnyZ (DC) 19:15:31 12/08/03
Post a Followup	You cannot reply to this message because you are not logged in.