Subject	Got new gauge rings installed. Thx SPL & Ted! =)
Posted by	FLYT300 on November 12, 2003 at 11:31 PM
	This message has been viewed 155 times.
Message	Not too hard on the installation. I didn't opt for any glue. (I hope I'm not sorry) They did seem to make a pretty "positive" fit. They looked good in my garage at night. If after a few days I like 'em, I may go back and glue 'em in place. Argh, gotta go update my profile! Happy ZX'n -Dan '93 TT Mar '02 - present '94 NA Jun '99- Mar '02 Best of Classified section: Posted by: megandnick@aol.com on June 27, 2002 at 7:38 am WANTED: Driveshaft vibration problem Posted by: haz0rd on May 06, 2002 at 11:45 am WANTED: Hard pipers Posted by: speedfreak on April 18, 2002 at 8:16 pm WANTED: poor college kid Posted by: CapZ on December 09, 2001 at 8:13 pm FOR SALE: doom light $10
Follow Ups	Got new gauge rings installed. Thx SPL & Ted! =) - FLYT300 23:31:57 11/12/03 go back and glue them in...they'll fall off otherwise (n/m) - Zeus 23:33:27 11/12/03 3 dabs of black silicon is all I used on each one. (n/m) - ni[X]it 23:38:24 11/12/03 better than nothing (n/m) - Zeus 23:39:47 11/12/03 how about 3 MS20426ad3-4 countersuck rivets, double blind? - ni[X]it 23:42:20 11/12/03 never heard of "countersuck" rivets...must be new *shrug (n/m) - Zeus 23:44:26 11/12/03 LOL (n/m) - BigTDogg (MA) 06:41:24 11/13/03 Link to instructions > - kuah@splparts.com 00:41:57 11/13/03 Good idea. I guess I'll just do it and avoid needle damage. (n/m) - FLYT300 23:41:52 11/12/03 Mine have been on for 4 months with no glue... still holding - M[ohio] 23:43:44 11/12/03 I know someone who had them installed at a shop - Zeus 23:48:53 11/12/03 using a carefull hand, and a small pair of pliers, - ni[X]it 23:50:46 11/12/03 You're friend should tell them Elmer's glue won't cut it ;) (n/m) - M[ohio] 23:53:17 11/12/03 but 4 out of 5 pre-schoolers recommend it. (n/m) - Zeus 23:54:35 11/12/03 for breakfast, Zeus, they recommend it for breakfast. (n/m) - hoss 23:57:15 11/12/03 lol (n/m) - Zeus 23:59:17 11/12/03 Try superglue, but be very careful... (n/m) - kuah@splparts.com 00:43:53 11/13/03 get those DPs installed - let's "re-roll".. ;) (n/m) - Scotts94z32 23:35:11 11/12/03 I hear ya! Save for a clutch and install and I'm good. (n/m) - FLYT300 23:43:41 11/12/03 Still at it? LOL (n/m) - Zster (Big Red) 01:19:25 11/13/03 LOL - always, dude... ALWAYS.... ;) glad to c 2 u r around (n/m) - Scotts94z32 07:05:59 11/13/03 I just got them too Dan. Haven't installed them yet.. but - SpeedyZX 23:50:28 11/12/03 No picture? Criminal! - SeedyROM 00:25:30 11/13/03 I hate everyone who has an older TT, but less miles than - SpeedyZX 00:32:01 11/13/03 Well, I'll pass you. I have put on 35,000 in 14 months (n/m) - SeedyROM 00:40:35 11/13/03 damn, but at least you drive it everyday :) (n/m) - ImTheDevil 00:48:21 11/13/03 Exactly!!!!!!!! (n/m) - SeedyROM 01:00:56 11/13/03 Mine is a daily driver. I drive 200+ miles every 3 days or - SpeedyZX 00:51:22 11/13/03 If it helps any, I'm really at 129,000 right now ;) - SeedyROM 01:01:23 11/13/03 8300 miles in a year and a month :( - Z PYRATE 00:55:14 11/13/03 8300 miles worth of donuts... that's amazing. LOL - SpeedyZX 01:06:52 11/13/03 I dont mind, powerslides, donuts, etc...its all fun to me :) (n/m) - Z PYRATE 08:57:16 11/13/03 where did you get the gauges that redline at 7200RPM?? (n/m) - takirb 08:56:39 11/13/03 No oil pressure reading at idle? (n/m) - Boosted_One (SoCal) 09:29:40 11/13/03 Yeah, replaced the sender and still nothing :( Bad gauge (n/m) - SeedyROM 13:08:13 11/13/03 Sorry. Wife had digi cam. I C you got one of the few BA sets - FLYT300 11:37:10 11/13/03
Post a Followup	You cannot reply to this message because you are not logged in.